Sears 247.88853 owner manual Assembly

Page 6

 

ASSEMBLY

 

 

 

Rear

 

Right

 

 

Front

Left

 

 

Discharge Chute

 

 

Handle & Handle

 

 

Panel Assembly

 

 

Chute

Shift

 

Rod

 

Crank

 

 

 

 

Electric

 

 

Start Cord

Figure 1

IMPORTANT: This unit is shipped with engine oil in the engine, but without gasoline. After assembly, see OPERATION section of this manual for fuel selection and fill-up.

Removing From Carton

Cut the corners of the carton and lay the sides flat on the ground. Remove all packing inserts.

Remove all loose parts. For a complete list of the loose parts, refer to the following section.

Move the snow thrower out of the carton.

Make certain all parts and literature have been removed before discarding the carton.

Tools Required

1.1/2" , 7/16”, 3/8” wrenches or a set of adjustable wrenches

2.Set of pliers

3.Set of philips head screw drivers

4.Funnel to fill up gasoline

Before Assembly

Disconnect spark plug wire and ground it against the engine to prevent unintended starting.

NOTE: All references in this manual to the left or right side of the snow thrower is from the operating position only. Exceptions, if any, will be specified.

Loose Parts

Your snow thrower has been assembled at the factory except the parts shipped loose in the carton. These are listed below.

(See Figure 1 .)

a.Handle and Handle Panel Assembly

b.Chute Assembly

c.Electric Start Cord

d.Two-piece Chute Crank Assembly

e.Shift Rod

f.Hardware Pack

Attaching Handle Assembly

Stretch out the control cables and place the handles and handle panel assembly on the floor. See Figure 2.

Position the two ends of the handles on the snow thrower frame as indicated by arrows in Figure 2. For your convenience, you may place the discharge chute on the chute opening. Align the two lower holes on each handle to the corresponding holes on the snow thrower frame.

6

Image 6
Contents Snow Thrower Table of Contents Warranty InformationSafe Operation Practices TrainingMaintenance & Storage Hardware Pack Assembly Attaching Chute Attaching Chute CrankAttaching Clutch Cables Attaching Shift Rod Attaching Turn TriggersChute Clean-Out Tool Lamp WiringFinal Adjustments Auger ControlSkid Shoe Tire Pressure Pneumatic TiresSkid Shoe Operation Knowing Your Snow ThrowerOperating Controls Stopping Snow Thrower Before Starting EngineElectric Starter To Start EngineFill Oil Cold StartTo Throw Snow To Engage DriveTo Engage Augers Recoil StarterOperating Tips Before StoppingTo Stop The Snow Thrower Maintenance General RecommendationsLubrication Engine Maintenance Check V-BeltsCheck Friction Wheel Changing Oil Spark PlugChecking Oil Level Nearby areas may exceed 150o F65oC. Avoid these areasService & Adjustments AdjustmentsAugers ServiceCarburetor Replacing BeltPush Between the friction wheel plate. See Figure Changing Friction Wheel RubberDrive Belt Reassemble new friction wheel rubber toCarburetor OFF-SEASON Storage Preparing the EngineTROUBLE-SHOOTING Problem Cause RemedyLabels List & Location 777I20727Repair Parts Key Description Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Polo Green Powder Black Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower ModelPage Key Part Description Qty Recoil Starter Carburetor Garantia DE Información Numero De ModeloPreparación Practicas Seguras DE OperacionCapacitación FuncionamientoMantenimiento & Almacenamiento Su responsabilidadConjunto DE Ferreteria DE Ferreteria 20 x16-18 x Ensamblado Fijacion De La Canaleta Fijacion De La Manivela De La CanaletaCanaleta de descarga Superior Pasador Casquillo plástico Manija de La canaletaManija De laFijacion De La Vara De Cambios Fijacion De Los Gatillos De GiroCableado de la Lámpara Herramienta de limpieza de la canaletaAjustes Finales Operacion Conociendo a su expulsor de nieveConozca Su Expulsor De Nieve Detencion Del Expulsor De Nieve Antes de poner en marcha el motorPara Poner En Marcha El Motor Llenado De AceiteComo Apagar El Motor Enganche De La PropulsionManejo De La Limpiadora De Nieve Consejos De Operacion Enganche De Las Espirales Sin FinPresion De La Ruedas Herramienta de limpieza de canale Broche de cabelloLubricacion MantenimientoRecomendaciones Generales Eje De EngranajesVerificar Las Correas En Verificar La Rueda De FricciónCambio De Aceite Mantenimiento Del MotorAceite De Motor BujiaService & Ajustes ServiceAjustes Plancha Raspadora Y Zapatas Deslizantes Reemplazo De La CorreaCorreas de la espiral sin fin Correa propulsora Nota Sea precavido para evitar apretar el cable de controlCambio De La Goma De La Rueda De Friccion Cubrierta del propulsorCarburador Preparación del Expulsor de Nieve Almacenamiento DE Fuera DE TemporadaPreparación del motor Carburador Drenaje del tazónProblema Causas Accion correctora Tabla DE Localizacion DE FallasCanada Sears Parts & Repair Center