Sears 247.88853 owner manual Attaching Clutch Cables

Page 8

then insert the end of the chute crank into the eye hole in the plastic bushing in the lower chute crank bracket. See Figure 6 .

Hairpin Clip

Plastic Bushing

Chute Crank

Flat Washer

 

Lower Chute

Flat Washer

Crank Bracket

Figure 6

•Place the other 3/8 ID flat washer (from the same group of hardware) on the end of the chute crank and insert hairpin clip into hole at the end of the chute crank. See Figure 6 .

•Adjust the chute bracket so that the spiral on the chute crank fully engages the teeth on the chute assembly. Tighten hardware (Figure 6) on the lower chute crank bracket, if loosened earlier.

•Slide the upper chute crank through the plastic bushing in the upper chute crank bracket and then into the lower chute crank. See Figure 7 . Align the holes on the two pieces of the chute crank, and secure with hairpin clip from group B of the hardware pack.

Upper

Chute

Crank

Upper

Hairpin Chute

ClipCrank

Bracket

Lower Chute

Crank

Figure 7

•Fully rotate the chute, using the chute crank, to make sure that it moves freely.

•Using a wrench, tighten the hex bolt and the hex nut on the upper chute crank bracket.

•Slip the cables that run from the handle panel to the chute into the cable guide located on top of the engine. See Figure 8 .

CableCable

Guide

Discharge

Chute

Figure 8

•Tighten all loose hardware on the handle assembly now.

Attaching Clutch Cables

The clutch control cables are attached to the snow thrower. For shipping purposes, if the cables are attached to the top of the engine with cable ties, cut the cable ties now. The Z ends of the clutch cables are hooked into the clutch grips on each handle.

•Ensure there is a hex jam nut threaded all the way up the threaded portion of the Z fitting; extras are supplied in the hardware pack. See Figure 9 .

•Place the clutch grip in the raised (up) position.

Outer portion

Z Fitting

 

of cut-out

Hex Jam

 

Nut

Hex Jam

Nut

Flats Ferrule

Barrel

(Viewed from the underside of the handle panel)

Figure 9

•Swing the left auger cable up making sure the cable is routed correctly in the cable roller guides located at the lower rear of the unit.

•Hold the end of the cable at the barrel so the ferrule turns freely without twisting the cable. Thread the ferrule on to the Z fitting. You may have to pull on the cable slightly to relieve tension. Keep the ferrule turning without twisting the cable.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Snow Thrower Table of Contents Warranty InformationSafe Operation Practices TrainingMaintenance & Storage Hardware Pack Assembly Attaching Chute Attaching Chute CrankAttaching Clutch Cables Attaching Shift Rod Attaching Turn TriggersLamp Wiring Final AdjustmentsChute Clean-Out Tool Auger ControlSkid Shoe Skid ShoeTire Pressure Pneumatic Tires Operating Controls OperationKnowing Your Snow Thrower Stopping Snow Thrower Before Starting EngineTo Start Engine Fill OilElectric Starter Cold StartTo Engage Drive To Engage AugersTo Throw Snow Recoil StarterTo Stop The Snow Thrower Operating TipsBefore Stopping Lubrication MaintenanceGeneral Recommendations Check Friction Wheel Engine MaintenanceCheck V-Belts Spark Plug Checking Oil LevelChanging Oil Nearby areas may exceed 150o F65oC. Avoid these areasService & Adjustments AdjustmentsService CarburetorAugers Replacing BeltPush Changing Friction Wheel Rubber Drive BeltBetween the friction wheel plate. See Figure Reassemble new friction wheel rubber toCarburetor OFF-SEASON Storage Preparing the EngineTROUBLE-SHOOTING Problem Cause RemedyLabels List & Location 777I20727Repair Parts Key Description Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Polo Green Powder Black Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower ModelPage Key Part Description Qty Recoil Starter Carburetor Garantia DE Información Numero De ModeloPracticas Seguras DE Operacion CapacitaciónPreparación FuncionamientoMantenimiento & Almacenamiento Su responsabilidad16-18 x Conjunto DE Ferreteria DE Ferreteria20 x Ensamblado Canaleta de descarga Fijacion De La CanaletaFijacion De La Manivela De La Canaleta Pasador Casquillo plástico Manija de La canaleta ManijaSuperior De laFijacion De La Vara De Cambios Fijacion De Los Gatillos De GiroAjustes Finales Cableado de la LámparaHerramienta de limpieza de la canaleta Conozca Su Expulsor De Nieve OperacionConociendo a su expulsor de nieve Detencion Del Expulsor De Nieve Antes de poner en marcha el motorPara Poner En Marcha El Motor Llenado De AceiteManejo De La Limpiadora De Nieve Como Apagar El MotorEnganche De La Propulsion Enganche De Las Espirales Sin Fin Presion De La RuedasConsejos De Operacion Herramienta de limpieza de canale Broche de cabelloMantenimiento Recomendaciones GeneralesLubricacion Eje De EngranajesVerificar Las Correas En Verificar La Rueda De FricciónMantenimiento Del Motor Aceite De MotorCambio De Aceite BujiaAjustes Service & AjustesService Correas de la espiral sin fin Plancha Raspadora Y Zapatas DeslizantesReemplazo De La Correa Correa propulsora Nota Sea precavido para evitar apretar el cable de controlCambio De La Goma De La Rueda De Friccion Cubrierta del propulsorCarburador Almacenamiento DE Fuera DE Temporada Preparación del motorPreparación del Expulsor de Nieve Carburador Drenaje del tazónProblema Causas Accion correctora Tabla DE Localizacion DE FallasCanada Sears Parts & Repair Center
Top Page Image Contents