Sears 247.88853 owner manual Push

Page 22

• Remove the six hex nuts and lock washers which

•

To remove the front auger drive belt, push the idler

attach the auger housing assembly to the frame

pulley to the left. See Figure 32 . The belt brake

assembly. See Figure 30.

should move outward. Lift the front auger drive

WARNING: Do not attempt to change the

belt from the front auger pulley.

auger belt without the help of an assistant. It is

very important that one person, standing at the

operating position, firmly hold the snow thrower

housing to prevent it from tipping while the

other person replaces the belt. Failure to

comply may cause injury.

Hex Nuts,

Lock

Washer	•

Align

studs for
reassembly	•

Auger

Idler Pulley

Figure 32

Place new belts on the two auger pulleys making sure that the front auger belt is under the belt brake. Route belts under and to the left of the flat idler pulley. Hold the belts upward in this position. While lifting up on the handles, bring the frame assembly close to the auger housing, and place the two belts on the front and rear engine pulleys. See Figure 33.

Figure 30

•Standing in the operating position, lift up on the handles and pull the frame assembly towards the rear. The frame and the housing will separate, and the rear auger belt will come off the pulley. Maintain control of the frame assembly while pulling it.

•Remove the two belts from the two engine pulleys. For location of the pulleys, see Figure 31 .

Auger Belt

Drive Belt

Rear

Engine

Pulley

Idler Pulley

Front

Engine

Pulley

Figure 31

Auger

Housing

PUSH

PUSH

Frame

Assembly

Figure 33

•Lift the frame assembly and tip the auger housing forward to align studs with the corresponding holes on both sides of the frame assembly. See Figure 30. Push the frame assembly fully on to the studs.

NOTE: Use care to avoid pinching the control cable.

•From the frame assembly side, insert six lock washers and hex nuts on to the studs . These pieces of hardware were removed earlier. See Figure 30. Tighten the nuts securely.

22

Image 22

Contents Snow Thrower Table of Contents Warranty InformationSafe Operation Practices TrainingMaintenance & Storage Hardware Pack Assembly Attaching Chute Attaching Chute CrankAttaching Clutch Cables Attaching Shift Rod Attaching Turn TriggersChute Clean-Out Tool Lamp WiringFinal Adjustments Auger ControlTire Pressure Pneumatic Tires Skid ShoeSkid Shoe Knowing Your Snow Thrower OperationOperating Controls Stopping Snow Thrower Before Starting EngineElectric Starter To Start EngineFill Oil Cold StartTo Throw Snow To Engage DriveTo Engage Augers Recoil StarterBefore Stopping Operating TipsTo Stop The Snow Thrower General Recommendations MaintenanceLubrication Check V-Belts Engine MaintenanceCheck Friction Wheel Changing Oil Spark PlugChecking Oil Level Nearby areas may exceed 150o F65oC. Avoid these areasService & Adjustments AdjustmentsAugers ServiceCarburetor Replacing BeltPush Between the friction wheel plate. See Figure Changing Friction Wheel RubberDrive Belt Reassemble new friction wheel rubber toCarburetor OFF-SEASON Storage Preparing the EngineTROUBLE-SHOOTING Problem Cause RemedyLabels List & Location 777I20727Repair Parts Key Description Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Polo Green Powder Black Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower ModelPage Key Part Description Qty Recoil Starter Carburetor Garantia DE Información Numero De ModeloPreparación Practicas Seguras DE OperacionCapacitación FuncionamientoMantenimiento & Almacenamiento Su responsabilidad20 x Conjunto DE Ferreteria DE Ferreteria16-18 x Ensamblado Fijacion De La Manivela De La Canaleta Fijacion De La CanaletaCanaleta de descarga Superior Pasador Casquillo plástico Manija de La canaletaManija De laFijacion De La Vara De Cambios Fijacion De Los Gatillos De GiroHerramienta de limpieza de la canaleta Cableado de la LámparaAjustes Finales Conociendo a su expulsor de nieve OperacionConozca Su Expulsor De Nieve Detencion Del Expulsor De Nieve Antes de poner en marcha el motorPara Poner En Marcha El Motor Llenado De AceiteEnganche De La Propulsion Como Apagar El MotorManejo De La Limpiadora De Nieve Consejos De Operacion Enganche De Las Espirales Sin FinPresion De La Ruedas Herramienta de limpieza de canale Broche de cabelloLubricacion MantenimientoRecomendaciones Generales Eje De EngranajesVerificar Las Correas En Verificar La Rueda De FricciónCambio De Aceite Mantenimiento Del MotorAceite De Motor BujiaService Service & AjustesAjustes Reemplazo De La Correa Plancha Raspadora Y Zapatas DeslizantesCorreas de la espiral sin fin Correa propulsora Nota Sea precavido para evitar apretar el cable de controlCambio De La Goma De La Rueda De Friccion Cubrierta del propulsorCarburador Preparación del Expulsor de Nieve Almacenamiento DE Fuera DE TemporadaPreparación del motor Carburador Drenaje del tazónProblema Causas Accion correctora Tabla DE Localizacion DE FallasCanada Sears Parts & Repair Center