Land Pride RBT55120 manual Hitch, Frame & Blade, Refer to Figure

Page 10

Table of Contents

Section 1: Assembly & Set-Up

Land Pride

Hitch, Frame & Blade

1.Locate shipping crate on a level surface. Remove & separate blade assemblies from shipping crate.

IMPORTANT: Do not remove shipping block from the blade tilt housing until all cylinders and/or ratchet jack and manual links have been installed.

Refer to Figure 1-1:

2.Use a lifting device to set blade pivot assembly (#9) upright. Remove bolts (#6), lock washers (#7) & pivot cap (#8) from blade pivot assembly (#9). Do not remove shipping block in the blade tilt housing.

3.Carefully insert blade pivot assembly (#9) into main frame (#2) at a 90˚ angle to the frame.

4.Reinstall pivot cap (#8), lockwashers (#7) and 3/4"-16 x 1 3/4" GR5 hex head cap screws (#6). Tighten hardware to secure main frame to blade pivot assembly.

5.Remove 3/4" x 4 3/8" hitch pin (#10) and rotate jack stand (#11) to a vertical position. Re-insert pin (#10) and secure with lock pin.

6.Lower unit to ground and unhook lifting device.

7.Remove front pivot shaft (#3) from front hitch assembly (#1) by removing 1/2" bolts (#5) and lock washer (#4).

8.Secure front hitch assembly (#1) to a lifting device or attach to a tractor. See “Tractor Hook-Up” on page 9.

9.Insert main frame (#2) into front hitch (#1) as shown. Reinstall front pivot shaft (#3) and secure with 1/2” lock washer(#4), 1/2"-13 x 1 1/2” GR5 bolts (#5). Tighten hardware to secure front pivot shaft (#3).

10.If not already done, attach unit to tractor

3-point hitch. The top 3-point hitch pin and linch pin are to be supplied by the customer. See Figure 1-3 on page 9 for category settings.

11.Re-check all hardware for tightness. Torque all bolts to specifications as listed in the “Torque Values Chart” on page 11.

!CAUTION!

Always check all hardware for tightness before using the blade. The moldboard will fall off if 3/4" bolts (#6) and/or 1/2" bolts (#12) are missing

SHIPPING BLOCK

DO NOT REMOVE UNTIL AFTER ALL

HYDRAULIC CYLINDERS AND/OR

RATCHET JACK AND MANUAL LINKS

HAVE BEEN INSTALLED.

Rear Blade Assembly

Figure 1-1

12888

 

8

RBT55120 Rear Blades 301-172M

5/21/07

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Rear Blades Table of Contents Safety at All Times Practice Safe Maintenance Use a Safety ChainTransport Machinery Safely Avoid High Pressure Fluids Hazard Wear Protective EquipmentKeep Riders Off Machinery Safety Labels 818-339C818-230C Owner Assistance Using This ManualApplication IntroductionAssembly & Set-Up Tractor RequirementsHitch, Frame & Blade Refer to FigureStandard & Quick Hitch Tractor Hook-UpCategory lll Category llBlade Offset Cylinder Options, Assembly & Set-UpBlade Angling Cylinder Blade Tilting Cylinder Manual Blade Angling Manual Blade Offset Manual Offset, Angling and TiltingManual Blade Tilting Hydraulic Cylinder Option Gauge WheelRatchet Jack Option Kit BundlesHydraulic Selector Valve Kit BundleEnd Plates Skid ShoeWear Plates Blade Offset AdjustmentsBlade Pitch Blade Angle and ReversingManual Gauge Wheel Adjustment Hydraulic Gauge Wheel AdjustmentOperating Check List Operating ChecklistOperating Procedures TransportingGeneral Operating Instructions Lubrication MaintenanceMaintenance & Lubrication HoursMoldboard and Blade Front Pivot ShaftRatchet Jack Gauge Wheel Caster Tube Gauge Wheel Front PivotGauge Wheel Hub RBT55120 Model Specifications & CapacitiesRBT55120 Features & Benefits Features BenefitsAppendix Torque Values ChartIn-tpi · m Ft-lb Mm x pitch 26 RBT55120 Rear Blades 301-172M Warranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Top Page Image Contents