Land Pride RBT55120 Blade Offset Cylinder, Blade Angling Cylinder, Options, Assembly & Set-Up

Page 12

Table of Contents

Section 2: Options, Assembly & Set-Up

Land Pride

Blade Offset Cylinder

Refer to Figure 2-1:

IMPORTANT: Do not remove shipping block from the blade tilt housing until all cylinders and/or ratchet jack and manual links have been installed.

IMPORTANT: Attach cylinder base to the front hitch lug. The cylinder base will interfere with the main frame if attached to the rear lug.

Assemble the hydraulic hoses to the hydraulic cylinder before placing the cylinder on the blade.

1.Position hydraulic cylinder (#3) with ports on top as shown. Install two straight fittings (#4) into the cylinder ports as shown. Tighten as needed.

2.Screw 116" long hydraulic hoses (#5) into straight fittings (#4) and tighten.

3.Thread adapter fittings (#6) to the other end of the hydraulic hoses and tighten. (Hydraulic couplings not furnished.)

4.Attach hydraulic cylinder to the lugs located on the left side of the 3-Way Rear Blade with clevis pins (#2). Make sure hydraulic ports are positioned on top and the cylinder base in positioned to the front as shown.

5.Secure clevis pins with hair pin cotters (#1).

Blade Angling Cylinder

Refer to Figure 2-2:

IMPORTANT: Do not remove shipping block from the blade tilt housing until all cylinders and/or ratchet jack and manual links have been installed.

IMPORTANT: Attach cylinder base to the front hitch lug. If attached to the rear lug, the base will interfere with the main frame.

1.Position hydraulic cylinder (#3) with ports on top as shown. Install two straight fittings (#4) into the cylinder ports as shown. Tighten as needed.

2.Screw 116" long hydraulic hoses (#5) into straight fittings (#4) and tighten.

3.Thread adapter fittings (#6) to the other end of the hydraulic hoses and tighten. (Hydraulic couplings not furnished.)

4.Attach hydraulic cylinder to the lugs on the right side of the frame with clevis pins (#1). Make sure hydraulic ports are positioned on top and the cylinder base in positioned to the front as shown.

5.Secure clevis pins with hair pin cotters (#2).

6.Route hoses through hose bracket located on the right side of the front hitch. Connect hoses to tractor's hydraulic system.

6.Route hoses through hose bracket located on the right side of the front hitch. Connect hoses to tractor's hydraulic system.

25502

25503

Hydraulic Blade Angling

Figure 2-2

Hydraulic Blade Offsetting

Figure 2-1

10 RBT55120 Rear Blades 301-172M

5/21/07

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Rear Blades Table of Contents Safety at All Times Use a Safety Chain Practice Safe MaintenanceTransport Machinery Safely Wear Protective Equipment Avoid High Pressure Fluids HazardKeep Riders Off Machinery Safety Labels 818-339C818-230C Using This Manual ApplicationOwner Assistance IntroductionAssembly & Set-Up Tractor RequirementsHitch, Frame & Blade Refer to FigureTractor Hook-Up Category lllStandard & Quick Hitch Category llOptions, Assembly & Set-Up Blade Offset CylinderBlade Angling Cylinder Blade Tilting Cylinder Manual Offset, Angling and Tilting Manual Blade Angling Manual Blade OffsetManual Blade Tilting Gauge Wheel Ratchet Jack OptionHydraulic Cylinder Option Kit BundlesHydraulic Selector Valve Kit BundleSkid Shoe End PlatesWear Plates Adjustments Blade PitchBlade Offset Blade Angle and ReversingManual Gauge Wheel Adjustment Hydraulic Gauge Wheel AdjustmentOperating Checklist Operating ProceduresOperating Check List TransportingGeneral Operating Instructions Maintenance Maintenance & LubricationLubrication HoursFront Pivot Shaft Moldboard and BladeRatchet Jack Gauge Wheel Front Pivot Gauge Wheel Caster TubeGauge Wheel Hub Specifications & Capacities RBT55120 ModelRBT55120 Features & Benefits Features BenefitsTorque Values Chart AppendixIn-tpi · m Ft-lb Mm x pitch 26 RBT55120 Rear Blades 301-172M Warranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Top Page Image Contents