Craftsman 536.88112 How To Install Speed Control Rod, How To Assemble Chute Deflector, Pin

Page 10

How To Install

The Speed Control Rod

1.Put the speed select lever into the sixth gear position.

2.Attach the speed control rod (end with 90 ° bend) to the speed select bracket with washer and cotter pin. See Figure 9.

3.Put the speed select lever into the first gear position.

,Attach the ball joint, located on the bottom end of the speed control rod, to the shift yoke assembly. See Figure 10. The fasteners are attached to the ball joint at the factory.

The length ot the ball joint and speed control rod have been pre-adjusted at

the factory. _f an adjustment is required, loosen the nut. Remove the fasteners

to disconnect the ball joint from the shift yoke assembly. To lengthen or shorten the speed control rod, turn the adapter to obtain the correct length.

5.Make sure the speed select lever functions correctly. Move the speed select lever through all speeds.

How To Assemble

The Chute Deflector

1.Remove the carriage bolt. See Figure 11.

2.Raise the chute deflector into op- erating position,

3.Fasten chute deflector to flange with carriage bolt. Make sure to

Operating Po_

Chute

Deft

Carriage

Flange W;

Bolt

_Lsher

_SpeedSelect

Speed ][Lever

Select

Bracket

Washer 3/8"

Pin

!

Speed

Control

Rod

Figure 9

Speed Control Rod

Adapter _

JointFasteners

Figure 10

install with head of the carriage bolt on the inside of the flange.

4.Fasten with washer and Iocknut.

5.Tighten Iocknut securely.

NOTE: Make sure all carriage

bolts in flange are tight. DO NOT OVERTIGHTEN.

6.Cut tie strap on chute deflector.

Nut

Tie Strap

Figure 11

F-001129J

10

Image 10
Contents Snow Thrower 001129JLimited TWO-YEAR Warranty on Craftsman Snow Thrower Wash Hands After HandlingTraining PreparationMaintenance and Storage Control And Operating SymbolsWhen snow thrower is transported or not Never operate the snow thrower without÷61 Contents of Parts Bag actual size Parts packed separately in carton not shown full sizeLever How To Remove The Snow Thrower From The CartonTools Required DeflectorNot Universal Joint How To Install The KnobsKnob KnobHow To Assemble Chute Deflector How To Install Speed Control RodPin Drive Cable Short How To Set Length Of The CablesCheck The Cables TractionAuger Drive CableHow To Set The Drift Cutters ChecklistKnow Your Snow Thrower RecoilTo Controlsnow Discharge HOW to Move Forward and BackwardTo Stop Your Snow Thrower To Throw SnowBefore Starting the Engine HOW to USE Wheel LockoutService & Adjustments section of this manual Fill GASTo Start Engine Electric STARTER, if Equipped To Stop EngineTo Start Engine Cold StartWarm Start Recoil StarterFrozen Starter Snow Throwing Tips General Recommendations Lubrication ChartCustomer Responsibilities After Each USEAS Required Product SpecificationsLubrication Every 10 Hours Lubrication EngineLUBRICATION-NOT Required To Change Engine OILTo Adjust Scraper BAR To Adjust Skid HeightWall maximum pressure on tire To Adjust Belts HOW to Check and Adjust the CablesHow To Adjust The Auger Drive Belt Tighten ,the nut How To Remove The Auger Drive BeltTo Replace Belts Traction Drive BeltOutdoors, away from fire or Traction Belt Guide Drive PulleyHOW to Adjust the Belt Guide HOW to Adjust or Replace the Friction WheelHow To Check The Friction Wheel Tighten nut on the speed control rod Tighten the bottom bolts on each side of the bottom panel HOW to Replace the Auger Shear BoltProtect the machine, use only To adjust To Adjust the CarburetorTo Adjust or Replace the Spark Plug Important Never tamper withScrews,are securely fastened. Thoroughly clean the snow throwerSnow Thrower Line outdoors, away fromDifficult starting Description Frame Assembly5359 319042Electric Start Assembly Craftsman 33 12.5HP Snow ThrowerFrame Assy BottomDrive Components 192Lever Drive ComponentsRET E Auger Housing Assembly Key306 340 321 327 330 304 316 Gear Case AssemblyKey Description 310Discharge Chute Assembly 5866OO Craftsman 33 12.5HP Snow Thrower 536.881120 Handleassembly Key Part Description Wheel Assembly 678 673KEY# REF. KEY# 337139 J Control Panel Assembly768 860 Chute Control ROD Assembly856 855 854 855862 867863 864 866 874LIGHT, Halogen Headlight621 626 628 627 622 Harness HeadlightRemote Chute Control Assembly 967 965966 968Drift Cutter Assembly 280Craftsman 4-CYCLE Engine Model Number Std KEY Part Description10-32 x 3/4 Flywheel Key185 37085 Intake Pipe 35187180 35954 282 650760 Screw 342 792028 Screw, 5/16-18 285 35985B 343 35079 Key Switch Bracket35703 33t25 KEY Part DescriptionCraftsman 4-CYCLE Engine Model Number Cover KEY Part 81AR8

536.88112 specifications

The Craftsman 536.88112 is a powerful and versatile snow thrower designed to tackle heavy snowfall and provide effective cleaning solutions for residential properties. With a combination of robust build quality and innovative features, this machine stands out in the market for both performance and ease of use.

One of the main features of the Craftsman 536.88112 is its powerful gas engine, which delivers significant torque to efficiently clear snow from driveways, sidewalks, and other surfaces. With a clearing width of approximately 24 inches, this snow thrower can handle large volumes of snow quickly, saving users valuable time during winter storms. The adjustable chute can rotate up to 180 degrees, allowing for precise control over snow direction and ensuring that you can clear pathways without unnecessary rework.

The machine incorporates an easy-start technology that ensures reliable ignition in cold weather, making it user-friendly even in the harshest winter conditions. It also features a six-speed transmission, which allows users to adjust the speed according to their preferences and the density of the snow being cleared. This flexibility makes the Craftsman 536.88112 suitable for various snow types, from light and fluffy powder to heavier, dense accumulations.

Another notable characteristic of the Craftsman 536.88112 is its durable construction. Built with heavy-duty materials, the snow thrower is designed to withstand the rigors of tough winter conditions, ensuring longevity and reliable performance throughout the season. Furthermore, the ergonomic handle and control layout are designed for maximum comfort, making it easier for users to maneuver the machine over large areas.

Maintaining the Craftsman 536.88112 is also straightforward, with features that facilitate regular upkeep. The easy-access oil drain and refill points, coupled with industry-standard maintenance protocols, help ensure that the engine remains in prime condition for years to come.

In conclusion, the Craftsman 536.88112 snow thrower is a reliable and efficient solution for homeowners looking to manage winter snowfall effectively. With its powerful engine, adjustable chute, and robust design, it stands as an excellent investment for those who face harsh winter conditions, ensuring that pathways remain clear and safe throughout the season.