Craftsman 536.88112 Outdoors, away from fire or, Traction Belt Guide Drive Pulley

Page 26

frame will separate, hinged bolts.

;,

Motor _ v _ ._

Mount ._..._i .-_ /

Frame I€_ _ [ /

Remov-' [M

bolt(each [ _ ....._'_7

by the

How

To Remove

the

Traction Drive

 

Belt

 

 

 

 

If the snow thrower will not move for-

°o.o=ward, check the traction drive belt for

_ Panel

 

 

 

 

V_._

wear

or damage. If the traction drive

, Auger

belt is worn or damaged, replace the

belt

as follows.

 

 

 

 

 

=oo=no

 

 

 

1. Remove the gas from the gas tank.

 

Stand the snow thrower up on the

\

front end of the

auger

housing.

(Each Side)

Figure 31

. Loosen the belt guide. Pull the belt guide away from the auger drive pulley. See Figure 29.

,Loosen the nut on the idler pulley. Pull the idler pulley away from the auger arive belt.

. Remove the old auger drive belt. Replace the auger drive belt with

an original factory replacement belt available from an authorized service

center.

9.Install the new auger drive belt onto the auger drive pulley and onto the drive pulley.

10.Adjust the auger drive belt. See "How To Adjust The Auger Drive

Belt" in the Service And Adjustment section.

11.Adjust the belt guide. See "How To Adjust The Belt Guide" in the Ser- vice And Adjustment section.

12.Install the bolts on each side of the motor mount frame. See

Figure 31.

13."lighten the bolts on each side of the motor mount frame.

14.Install the belt cover. Tighten the screw. See Figure 28.

15.Check the adjustment of the cables. See "How To Check And Adjust The Cables" in the Service And Adjust- ment section.

16, Connect the spark plug wire.

outdoors, away from fire or

,_ WARNING: Drain the gasoline flame,

. Disconnect the spark plug wire.

3.Remove the auger drive belt. See

"How To Remove The Auger Drive Belt" in the Maintenance section.

4.Pull the traction drive idler pulley away from the traction drive belt.

See Figure 32.

Traction Drive Belt

Auger Drive

.=It

Traction

Belt Guide

Drive Pulley

 

Auger

Drive

Pulley

Traction

DriveAuger

IdlerIdler

PulleyPulley

Engine Pulley

Figure 32

. Remove the old traction drive belt

from the traction drive pulley and from the engine pulley. Replace the traction drive belt with an original

factory replacement belt available from an authorized service center.

6.Install the new traction drive belt onto the traction drive pulley and onto the engine pulley.

7.Make sure the traction drive idler

pulley is properly aligned with the traction drive belt.

,Install and adjust the auger drive belt. See "How To Remove The Au-

F-001129J

26

Image 26
Contents Snow Thrower 001129JLimited TWO-YEAR Warranty on Craftsman Snow Thrower Wash Hands After HandlingTraining PreparationMaintenance and Storage Control And Operating SymbolsWhen snow thrower is transported or not Never operate the snow thrower without÷61 Contents of Parts Bag actual size Parts packed separately in carton not shown full sizeLever How To Remove The Snow Thrower From The CartonTools Required DeflectorNot Universal Joint How To Install The KnobsKnob KnobPin How To Install Speed Control RodHow To Assemble Chute Deflector Drive Cable Short How To Set Length Of The CablesCheck The Cables TractionAuger Drive CableHow To Set The Drift Cutters ChecklistKnow Your Snow Thrower RecoilTo Controlsnow Discharge HOW to Move Forward and BackwardTo Stop Your Snow Thrower To Throw SnowBefore Starting the Engine HOW to USE Wheel LockoutService & Adjustments section of this manual Fill GASTo Start Engine Electric STARTER, if Equipped To Stop EngineTo Start Engine Cold StartWarm Start Recoil StarterFrozen Starter Snow Throwing Tips General Recommendations Lubrication ChartCustomer Responsibilities After Each USELubrication Every 10 Hours Product SpecificationsAS Required Lubrication EngineLUBRICATION-NOT Required To Change Engine OILWall maximum pressure on tire To Adjust Skid HeightTo Adjust Scraper BAR How To Adjust The Auger Drive Belt HOW to Check and Adjust the CablesTo Adjust Belts Tighten ,the nut How To Remove The Auger Drive BeltTo Replace Belts Traction Drive BeltOutdoors, away from fire or Traction Belt Guide Drive PulleyHow To Check The Friction Wheel HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide Tighten nut on the speed control rod Protect the machine, use only HOW to Replace the Auger Shear BoltTighten the bottom bolts on each side of the bottom panel To adjust To Adjust the CarburetorTo Adjust or Replace the Spark Plug Important Never tamper withScrews,are securely fastened. Thoroughly clean the snow throwerSnow Thrower Line outdoors, away fromDifficult starting Description Frame Assembly5359 319042Electric Start Assembly Craftsman 33 12.5HP Snow ThrowerFrame Assy BottomDrive Components 192RET E Drive ComponentsLever Auger Housing Assembly Key306 340 321 327 330 304 316 Gear Case AssemblyKey Description 310Discharge Chute Assembly 5866OO Craftsman 33 12.5HP Snow Thrower 536.881120 Handleassembly Key Part Description Wheel Assembly 678 673768 Control Panel AssemblyKEY# REF. KEY# 337139 J 860 Chute Control ROD Assembly856 855 854 855862 867863 864 866 874LIGHT, Halogen Headlight621 626 628 627 622 Harness HeadlightRemote Chute Control Assembly 967 965966 968Drift Cutter Assembly 280Craftsman 4-CYCLE Engine Model Number Std KEY Part Description10-32 x 3/4 Flywheel Key180 35954 35187185 37085 Intake Pipe 35703 343 35079 Key Switch Bracket282 650760 Screw 342 792028 Screw, 5/16-18 285 35985B 33t25 KEY Part DescriptionCraftsman 4-CYCLE Engine Model Number Cover KEY Part 81AR8

536.88112 specifications

The Craftsman 536.88112 is a powerful and versatile snow thrower designed to tackle heavy snowfall and provide effective cleaning solutions for residential properties. With a combination of robust build quality and innovative features, this machine stands out in the market for both performance and ease of use.

One of the main features of the Craftsman 536.88112 is its powerful gas engine, which delivers significant torque to efficiently clear snow from driveways, sidewalks, and other surfaces. With a clearing width of approximately 24 inches, this snow thrower can handle large volumes of snow quickly, saving users valuable time during winter storms. The adjustable chute can rotate up to 180 degrees, allowing for precise control over snow direction and ensuring that you can clear pathways without unnecessary rework.

The machine incorporates an easy-start technology that ensures reliable ignition in cold weather, making it user-friendly even in the harshest winter conditions. It also features a six-speed transmission, which allows users to adjust the speed according to their preferences and the density of the snow being cleared. This flexibility makes the Craftsman 536.88112 suitable for various snow types, from light and fluffy powder to heavier, dense accumulations.

Another notable characteristic of the Craftsman 536.88112 is its durable construction. Built with heavy-duty materials, the snow thrower is designed to withstand the rigors of tough winter conditions, ensuring longevity and reliable performance throughout the season. Furthermore, the ergonomic handle and control layout are designed for maximum comfort, making it easier for users to maneuver the machine over large areas.

Maintaining the Craftsman 536.88112 is also straightforward, with features that facilitate regular upkeep. The easy-access oil drain and refill points, coupled with industry-standard maintenance protocols, help ensure that the engine remains in prime condition for years to come.

In conclusion, the Craftsman 536.88112 snow thrower is a reliable and efficient solution for homeowners looking to manage winter snowfall effectively. With its powerful engine, adjustable chute, and robust design, it stands as an excellent investment for those who face harsh winter conditions, ensuring that pathways remain clear and safe throughout the season.