Craftsman 536.88112 HOW to Replace the Auger Shear Bolt, Protect the machine, use only

Page 29

8.Remove the four bolts that hold the bearing plates on each side of the hex shaft. See Figure 38.

NOTE: Take special note of the position of the washers and retain- ing ring on the hex shaft and the sprocket assembly.

Friction Wheel Hex Shaft

Bearing

Bearing

Plate

Plate

Figure 38

g.Remove the bearing plate from the right side. Do not remove the hex shaft. Leave the hex shaft in posi- tion. Carefully raise hex shaft just

enough to allow the friction wheel to be removed.

10.Remove the friction wheel from the

hub. Slip the friction wheel toward the right off the hex shaft. See Figure 37.

11.Assemble the new friction wheel onto hub with the fasteners re- moved earlier.

12.Install the bearing plate onto the right side. Make sure the hex shaft is engaged with both bearing

plates and that the washers and re- taining ring are installed in the origi- nal position. See Figure 38.

13.Fasten the bearing plates using the four bolts removed earlier.

14.Make sure the hex shaft turns free- ly.

15.Attach the speed control rod to the shift yoke assembly. See

Figure 36.

16.Check the adjustment of the friction

wheel. See "How To Adjust The Friction Wheel" in this section.

17.Make sure the friction wheel and the

disc drive plate are free from grease or oil.

18.Install the bottom panel. See Figure 34.

19.Tighten the bottom bolts on each side of the bottom panel.

20.Install the top bolts on each side of the bottom panel.

21.Connect the spark plug wire.

HOW TO REPLACE THE AUGER SHEAR BOLT

The augers are secured to the auger shaft with special shear bolts. These shear bolts are designed to break and protect the ma- chine if an object becomes lodged in the au- ger housing. Do not use a harder bolt as the

protection provided by the shear bolt will be lost.

protect the machine, use only

,_WARNING: For safety and to original equipment shear bolts.

. Move the throttle control to the stop position. Disengage all controls.

2.Disconnect the spark plug wire. Make sure all moving parts have stopped.

To replace a broken shear bolt, proceed as follows. Extra shear bolts were pro- vided in the assembly parts bag.

F--O01129J29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents 001129J Snow ThrowerWash Hands After Handling Limited TWO-YEAR Warranty on Craftsman Snow ThrowerPreparation TrainingWhen snow thrower is transported or not Control And Operating SymbolsMaintenance and Storage Never operate the snow thrower without÷61 Parts packed separately in carton not shown full size Contents of Parts Bag actual sizeTools Required How To Remove The Snow Thrower From The CartonLever DeflectorNot Knob How To Install The KnobsUniversal Joint KnobPin How To Install Speed Control RodHow To Assemble Chute Deflector Check The Cables How To Set Length Of The CablesDrive Cable Short TractionAuger Drive CableChecklist How To Set The Drift CuttersRecoil Know Your Snow ThrowerTo Stop Your Snow Thrower HOW to Move Forward and BackwardTo Controlsnow Discharge To Throw SnowService & Adjustments section of this manual HOW to USE Wheel LockoutBefore Starting the Engine Fill GASTo Stop Engine To Start Engine Electric STARTER, if EquippedWarm Start Cold StartTo Start Engine Recoil StarterFrozen Starter Snow Throwing Tips Customer Responsibilities Lubrication ChartGeneral Recommendations After Each USELubrication Every 10 Hours Product SpecificationsAS Required LUBRICATION-NOT Required EngineLubrication To Change Engine OILWall maximum pressure on tire To Adjust Skid HeightTo Adjust Scraper BAR How To Adjust The Auger Drive Belt HOW to Check and Adjust the CablesTo Adjust Belts To Replace Belts How To Remove The Auger Drive BeltTighten ,the nut Traction Drive BeltTraction Belt Guide Drive Pulley Outdoors, away from fire orHow To Check The Friction Wheel HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide Tighten nut on the speed control rod Protect the machine, use only HOW to Replace the Auger Shear BoltTighten the bottom bolts on each side of the bottom panel To Adjust or Replace the Spark Plug To Adjust the CarburetorTo adjust Important Never tamper withSnow Thrower Thoroughly clean the snow throwerScrews,are securely fastened. Line outdoors, away fromDifficult starting 5359 Frame AssemblyDescription 319042Craftsman 33 12.5HP Snow Thrower Electric Start AssemblyBottom Frame Assy192 Drive ComponentsRET E Drive ComponentsLever Key Auger Housing AssemblyKey Description Gear Case Assembly306 340 321 327 330 304 316 310586 Discharge Chute Assembly6OO Craftsman 33 12.5HP Snow Thrower 536.881120 Handleassembly Key Part Description 678 673 Wheel Assembly768 Control Panel AssemblyKEY# REF. KEY# 337139 J 856 855 854 855862 Chute Control ROD Assembly860 867863 864 866 874621 626 628 627 622 HeadlightLIGHT, Halogen Harness HeadlightRemote Chute Control Assembly 966 965967 968280 Drift Cutter AssemblyCraftsman 4-CYCLE Engine Model Number 10-32 x 3/4 KEY Part DescriptionStd Flywheel Key180 35954 35187185 37085 Intake Pipe 35703 343 35079 Key Switch Bracket282 650760 Screw 342 792028 Screw, 5/16-18 285 35985B 33t25 Description KEY PartCraftsman 4-CYCLE Engine Model Number Cover KEY Part 81AR8

536.88112 specifications

The Craftsman 536.88112 is a powerful and versatile snow thrower designed to tackle heavy snowfall and provide effective cleaning solutions for residential properties. With a combination of robust build quality and innovative features, this machine stands out in the market for both performance and ease of use.

One of the main features of the Craftsman 536.88112 is its powerful gas engine, which delivers significant torque to efficiently clear snow from driveways, sidewalks, and other surfaces. With a clearing width of approximately 24 inches, this snow thrower can handle large volumes of snow quickly, saving users valuable time during winter storms. The adjustable chute can rotate up to 180 degrees, allowing for precise control over snow direction and ensuring that you can clear pathways without unnecessary rework.

The machine incorporates an easy-start technology that ensures reliable ignition in cold weather, making it user-friendly even in the harshest winter conditions. It also features a six-speed transmission, which allows users to adjust the speed according to their preferences and the density of the snow being cleared. This flexibility makes the Craftsman 536.88112 suitable for various snow types, from light and fluffy powder to heavier, dense accumulations.

Another notable characteristic of the Craftsman 536.88112 is its durable construction. Built with heavy-duty materials, the snow thrower is designed to withstand the rigors of tough winter conditions, ensuring longevity and reliable performance throughout the season. Furthermore, the ergonomic handle and control layout are designed for maximum comfort, making it easier for users to maneuver the machine over large areas.

Maintaining the Craftsman 536.88112 is also straightforward, with features that facilitate regular upkeep. The easy-access oil drain and refill points, coupled with industry-standard maintenance protocols, help ensure that the engine remains in prime condition for years to come.

In conclusion, the Craftsman 536.88112 snow thrower is a reliable and efficient solution for homeowners looking to manage winter snowfall effectively. With its powerful engine, adjustable chute, and robust design, it stands as an excellent investment for those who face harsh winter conditions, ensuring that pathways remain clear and safe throughout the season.
Top Page Image Contents