Craftsman 536.88112 HOW to USE Wheel Lockout, Before Starting the Engine, Fill GAS, Check the OIL

Page 15

HOW TO USE

THE WHEEL LOCKOUT

The left wheel is secured to the axle with a lockout pin. See Figure 19. The unit was shipped with the lockout pin in the locked position. For ease of maneu- verability in light snow conditions, dis- connect the lockout pin as follows.

1.Pull the knob out to disengage the lockout pin.

2.To lock in the disengaged position, turn the knob 1/4 turn (90 degrees).

5.Check tire pressure (14-17

pounds). Do not exceed maximum amount of pressure.

CHECK THE OIL:

NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed.

1.Make sure the unit is level.

NOTE: Do not check the level of the oil while the engine runs.

2.Remove the oil fill cap/dipstick. Check the oil.

3.If necessary, add oil until the oil reaches the FULL mark on the oil fill cap/dipstick (see Figure 20). Do not add too much oil.

OII FillC_p/Dipstick

Knob

Wheel

Lockout

Figure 19

BEFORE STARTING THE ENGINE

,Before you service or start the en- gine, familiarize yourself with the

snow thrower. Be sure you under- stand the function and location of all

controls.

2.Check the tension of clutch cable before starting the engine. See To Adjust The Control Cable para-

graph in the Service & Adjust- ments section of this manual.

3.Be sure that all fasteners are tight.

4.Make sure the height adjust skids are properly adjusted. See To Ad- just Skid Height paragraph in the

Service & Adjustments section of this manual.

>{J_ _'_ NOTE: Oil level

_._ must be between full and Add mark

Figure 20

4.Tighten the fill cap/dipstick securely each time you check the oil level.

NOTE: For extreme cold operating conditions of 0°F and below, use a partial synthetic 0W30 motor oil for easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make starting easier in areas where temperature is consis- tently 20°1=. or lower.

FILL GAS:

NOTICE: ENGINES WHICH ARE CERTIFIED TO COMPLY WITH CAL- IFORNIA AND US EPA EMISSION REGULATIONS FOR ULGE ENGINES: Are certified to operate on regular un- leaded gasoline. Include the following emission control system(s): EM, TWC (if so equipped). Include any user ad- justable features-therefore no other ad- justments are needed.

F-001129J15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 001129J Snow ThrowerWash Hands After Handling Limited TWO-YEAR Warranty on Craftsman Snow ThrowerPreparation TrainingNever operate the snow thrower without Control And Operating SymbolsWhen snow thrower is transported or not Maintenance and Storage÷61 Parts packed separately in carton not shown full size Contents of Parts Bag actual sizeDeflector How To Remove The Snow Thrower From The CartonTools Required LeverNot Knob How To Install The KnobsKnob Universal JointHow To Install Speed Control Rod How To Assemble Chute DeflectorPin TractionAuger Drive Cable How To Set Length Of The CablesCheck The Cables Drive Cable ShortChecklist How To Set The Drift CuttersRecoil Know Your Snow ThrowerTo Throw Snow HOW to Move Forward and BackwardTo Stop Your Snow Thrower To Controlsnow DischargeFill GAS HOW to USE Wheel LockoutService & Adjustments section of this manual Before Starting the EngineTo Stop Engine To Start Engine Electric STARTER, if EquippedRecoil Starter Cold StartWarm Start To Start EngineFrozen Starter Snow Throwing Tips After Each USE Lubrication ChartCustomer Responsibilities General RecommendationsProduct Specifications AS RequiredLubrication Every 10 Hours To Change Engine OIL EngineLUBRICATION-NOT Required LubricationTo Adjust Skid Height To Adjust Scraper BARWall maximum pressure on tire HOW to Check and Adjust the Cables To Adjust BeltsHow To Adjust The Auger Drive Belt Traction Drive Belt How To Remove The Auger Drive BeltTo Replace Belts Tighten ,the nutTraction Belt Guide Drive Pulley Outdoors, away from fire orHOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideHow To Check The Friction Wheel Tighten nut on the speed control rod HOW to Replace the Auger Shear Bolt Tighten the bottom bolts on each side of the bottom panelProtect the machine, use only Important Never tamper with To Adjust the CarburetorTo Adjust or Replace the Spark Plug To adjustLine outdoors, away from Thoroughly clean the snow throwerSnow Thrower Screws,are securely fastened.Difficult starting 319042 Frame Assembly5359 DescriptionCraftsman 33 12.5HP Snow Thrower Electric Start AssemblyBottom Frame Assy192 Drive ComponentsDrive Components LeverRET E Key Auger Housing Assembly310 Gear Case AssemblyKey Description 306 340 321 327 330 304 316586 Discharge Chute Assembly6OO Craftsman 33 12.5HP Snow Thrower 536.881120 Handleassembly Key Part Description 678 673 Wheel AssemblyControl Panel Assembly KEY# REF. KEY# 337139 J768 867863 864 866 874 Chute Control ROD Assembly856 855 854 855862 860Harness Headlight Headlight621 626 628 627 622 LIGHT, HalogenRemote Chute Control Assembly 968 965966 967280 Drift Cutter AssemblyCraftsman 4-CYCLE Engine Model Number Flywheel Key KEY Part Description10-32 x 3/4 Std35187 185 37085 Intake Pipe180 35954 343 35079 Key Switch Bracket 282 650760 Screw 342 792028 Screw, 5/16-18 285 35985B35703 33t25 Description KEY PartCraftsman 4-CYCLE Engine Model Number Cover KEY Part 81AR8

536.88112 specifications

The Craftsman 536.88112 is a powerful and versatile snow thrower designed to tackle heavy snowfall and provide effective cleaning solutions for residential properties. With a combination of robust build quality and innovative features, this machine stands out in the market for both performance and ease of use.

One of the main features of the Craftsman 536.88112 is its powerful gas engine, which delivers significant torque to efficiently clear snow from driveways, sidewalks, and other surfaces. With a clearing width of approximately 24 inches, this snow thrower can handle large volumes of snow quickly, saving users valuable time during winter storms. The adjustable chute can rotate up to 180 degrees, allowing for precise control over snow direction and ensuring that you can clear pathways without unnecessary rework.

The machine incorporates an easy-start technology that ensures reliable ignition in cold weather, making it user-friendly even in the harshest winter conditions. It also features a six-speed transmission, which allows users to adjust the speed according to their preferences and the density of the snow being cleared. This flexibility makes the Craftsman 536.88112 suitable for various snow types, from light and fluffy powder to heavier, dense accumulations.

Another notable characteristic of the Craftsman 536.88112 is its durable construction. Built with heavy-duty materials, the snow thrower is designed to withstand the rigors of tough winter conditions, ensuring longevity and reliable performance throughout the season. Furthermore, the ergonomic handle and control layout are designed for maximum comfort, making it easier for users to maneuver the machine over large areas.

Maintaining the Craftsman 536.88112 is also straightforward, with features that facilitate regular upkeep. The easy-access oil drain and refill points, coupled with industry-standard maintenance protocols, help ensure that the engine remains in prime condition for years to come.

In conclusion, the Craftsman 536.88112 snow thrower is a reliable and efficient solution for homeowners looking to manage winter snowfall effectively. With its powerful engine, adjustable chute, and robust design, it stands as an excellent investment for those who face harsh winter conditions, ensuring that pathways remain clear and safe throughout the season.
Top Page Image Contents