Craftsman 536.88112 Product Specifications, AS Required, Lubrication Every 10 Hours

Page 21

PRODUCT SPECIFICATIONS

HORSEPOWER

12.5

HP

 

DISPLACEMENT

21.82

cu. in.

GASOLINE

4 quarts

 

CAPACITY

(unleaded)

 

OIL CAPACITY

5W30

 

 

20 oz

capacity)

 

 

 

SPARK

PLUG:

Champion

RJ19LM

 

 

(Gap

.030 in.) or

 

 

equivalent

 

VALVE

CLEARANCE:

Intake: .010 In.

 

 

Exhaust:

.010 In.

p.

SNOW THROWER

AS REQUIRED

The following adjustment should be preformed more than once each sea- son.

. Auger drive belt should be adjusted after the first 2 to 4 hours of use, again about mid-season and twice each season thereafter (See to Ad-

just Belts paragraph in the Ser- vice and Adjustment section),

LUBRICATION - EVERY 10 HOURS

. Auger Shaft - Using a hand grease gun, lubricate the auger shaft zerk

fittings (A) every ten (10) operating hours. Each time a shear bolt is re-

placed, the auger shaft MUST be greased. See Figure 22. See To

Replace Auger Shear Bolt in the Service and Adjustment section.

Figure 22

LUBRICATION-EVERY 25 HOURS

Lubricate Disc Drive Plate every twenty-five (25) hours and at the end of the season and/or before storage.

To Lubricate

1.Position speed selector lever in first gear.

2.Stand the snow thrower up on the auger housing end.

3.Remove the bottom panel.

4.Turn disc drive plate clockwise by

hand until grease zerk is clearly visible at front center. See

Figure 23.

5.Place a coin or (a shim of equal

thickness) between the rubber fric- tion wheel and disc drive plate to prevent rubber friction wheel con- tacting the drive disc plate.

6.To grease zerk, use a hand grease gun, lubricate with a Hi Temp EP Moly grease. Fill zerk only until grease becomes visible below bear-

ing assembly located under grease zerk. DO NOT over fill.

CAUTION: DO NOT allow grease to come in contract with the disc drive

plate or friction wheel or damage will result.

IMPORTANT: Remove coin and en-

sure that a gap exists between friction

wheel and disc drive plate.

F-001129J21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 001129J Snow ThrowerWash Hands After Handling Limited TWO-YEAR Warranty on Craftsman Snow ThrowerPreparation TrainingWhen snow thrower is transported or not Control And Operating SymbolsMaintenance and Storage Never operate the snow thrower without÷61 Parts packed separately in carton not shown full size Contents of Parts Bag actual sizeTools Required How To Remove The Snow Thrower From The CartonLever DeflectorNot Knob How To Install The KnobsUniversal Joint KnobHow To Install Speed Control Rod How To Assemble Chute DeflectorPin Check The Cables How To Set Length Of The CablesDrive Cable Short TractionAuger Drive CableChecklist How To Set The Drift CuttersRecoil Know Your Snow ThrowerTo Stop Your Snow Thrower HOW to Move Forward and BackwardTo Controlsnow Discharge To Throw SnowService & Adjustments section of this manual HOW to USE Wheel LockoutBefore Starting the Engine Fill GASTo Stop Engine To Start Engine Electric STARTER, if EquippedWarm Start Cold StartTo Start Engine Recoil StarterFrozen Starter Snow Throwing Tips Customer Responsibilities Lubrication ChartGeneral Recommendations After Each USEProduct Specifications AS RequiredLubrication Every 10 Hours LUBRICATION-NOT Required EngineLubrication To Change Engine OILTo Adjust Skid Height To Adjust Scraper BARWall maximum pressure on tire HOW to Check and Adjust the Cables To Adjust BeltsHow To Adjust The Auger Drive Belt To Replace Belts How To Remove The Auger Drive BeltTighten ,the nut Traction Drive BeltTraction Belt Guide Drive Pulley Outdoors, away from fire orHOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideHow To Check The Friction Wheel Tighten nut on the speed control rod HOW to Replace the Auger Shear Bolt Tighten the bottom bolts on each side of the bottom panelProtect the machine, use only To Adjust or Replace the Spark Plug To Adjust the CarburetorTo adjust Important Never tamper withSnow Thrower Thoroughly clean the snow throwerScrews,are securely fastened. Line outdoors, away fromDifficult starting 5359 Frame AssemblyDescription 319042Craftsman 33 12.5HP Snow Thrower Electric Start AssemblyBottom Frame Assy192 Drive ComponentsDrive Components LeverRET E Key Auger Housing AssemblyKey Description Gear Case Assembly306 340 321 327 330 304 316 310586 Discharge Chute Assembly6OO Craftsman 33 12.5HP Snow Thrower 536.881120 Handleassembly Key Part Description 678 673 Wheel AssemblyControl Panel Assembly KEY# REF. KEY# 337139 J768 856 855 854 855862 Chute Control ROD Assembly860 867863 864 866 874621 626 628 627 622 HeadlightLIGHT, Halogen Harness HeadlightRemote Chute Control Assembly 966 965967 968280 Drift Cutter AssemblyCraftsman 4-CYCLE Engine Model Number 10-32 x 3/4 KEY Part DescriptionStd Flywheel Key35187 185 37085 Intake Pipe180 35954 343 35079 Key Switch Bracket 282 650760 Screw 342 792028 Screw, 5/16-18 285 35985B35703 33t25 Description KEY PartCraftsman 4-CYCLE Engine Model Number Cover KEY Part 81AR8

536.88112 specifications

The Craftsman 536.88112 is a powerful and versatile snow thrower designed to tackle heavy snowfall and provide effective cleaning solutions for residential properties. With a combination of robust build quality and innovative features, this machine stands out in the market for both performance and ease of use.

One of the main features of the Craftsman 536.88112 is its powerful gas engine, which delivers significant torque to efficiently clear snow from driveways, sidewalks, and other surfaces. With a clearing width of approximately 24 inches, this snow thrower can handle large volumes of snow quickly, saving users valuable time during winter storms. The adjustable chute can rotate up to 180 degrees, allowing for precise control over snow direction and ensuring that you can clear pathways without unnecessary rework.

The machine incorporates an easy-start technology that ensures reliable ignition in cold weather, making it user-friendly even in the harshest winter conditions. It also features a six-speed transmission, which allows users to adjust the speed according to their preferences and the density of the snow being cleared. This flexibility makes the Craftsman 536.88112 suitable for various snow types, from light and fluffy powder to heavier, dense accumulations.

Another notable characteristic of the Craftsman 536.88112 is its durable construction. Built with heavy-duty materials, the snow thrower is designed to withstand the rigors of tough winter conditions, ensuring longevity and reliable performance throughout the season. Furthermore, the ergonomic handle and control layout are designed for maximum comfort, making it easier for users to maneuver the machine over large areas.

Maintaining the Craftsman 536.88112 is also straightforward, with features that facilitate regular upkeep. The easy-access oil drain and refill points, coupled with industry-standard maintenance protocols, help ensure that the engine remains in prime condition for years to come.

In conclusion, the Craftsman 536.88112 snow thrower is a reliable and efficient solution for homeowners looking to manage winter snowfall effectively. With its powerful engine, adjustable chute, and robust design, it stands as an excellent investment for those who face harsh winter conditions, ensuring that pathways remain clear and safe throughout the season.
Top Page Image Contents