Craftsman 536.88112 To Adjust Skid Height, To Adjust Scraper BAR, Wall maximum pressure on tire

Page 23

nect the spark plug wire and

,_ WARNING: Always discon- place it where it cannot

make contact with spark plug to pre- vent accidental starting when mak- ing any adjustments or repairs.

TO ADJUST SKID HEIGHT

This snow thrower is equipped with two

height adjustment skids, located on the outside of the auger housing. See

Figure 25.

These skids elevate the front of the snow thrower.

Mountinc Nuts

,, O

Auger

_g

Height Adjust Skid

Figure 25

For normal hard surfaces, such as a

paved driveway or walk, adjust the skids as follows.

1.Position the snow thrower on a level surface.

. Make sure both tires are equally in- flated. Proper tire pressure is 14 to 17 PSI. See side of tire for maxi- mum inflation. Do not exceed side- wall maximum pressure on tire.

3.Place the extra shear bolts supplied (found in parts bag) under each end of the scraper bar next to the adjustable skids.

4.Loosen the mounting nuts that hold the adjustable skids. To bring the front of the snow thrower down,

raise the adjustable skids. Tighten the mounting nuts. See Figure 25.

NOTE: For rocky or uneven surfaces, raise the front of the snow thrower by moving the skids down.

maintain proper ground

,_ WARNING: Be certain to clearance for your particular

area to be cleared. Objects such as gravel, rocks or other debris, if struck by the impeller, may be thrown with sufficient force to cause personal injury, property damage or damage to the snow thrower.

TO ADJUST SCRAPER BAR

After considerable use, the metal scrap- er bar will have a definite wear pattern. The scraper bar in conjunction with the skids should always be adjusted to al- low 1/8" between the scraper bar and the sidewalk or area to be cleaned.

1.Position the snow thrower on alevel surface.

. Make sure both tires are equally in-

flated. Proper tire pressure is 14 to 17 PSI. See side of tire for maxi- mum inflation. Do not exceed side-

wall maximum pressure on tire.

3.Loosen the carriage bolts and nuts securing the scraper bar to the au- ger housing.

4.Adjust the scraper bar to the proper position.

5.Tighten the carriage bolts and nuts, making sure that the scraper bar is parallel with the working surface.

. For extended operation, the scraper bar may be reversed. If the scraper bar must be replaced due to wear, remove the carriage bolts and nuts and install a new scraper bar.

F-001129J

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 001129J Snow ThrowerWash Hands After Handling Limited TWO-YEAR Warranty on Craftsman Snow ThrowerPreparation TrainingNever operate the snow thrower without Control And Operating SymbolsWhen snow thrower is transported or not Maintenance and Storage÷61 Parts packed separately in carton not shown full size Contents of Parts Bag actual sizeDeflector How To Remove The Snow Thrower From The CartonTools Required LeverNot Knob How To Install The KnobsKnob Universal JointPin How To Install Speed Control RodHow To Assemble Chute Deflector TractionAuger Drive Cable How To Set Length Of The CablesCheck The Cables Drive Cable ShortChecklist How To Set The Drift CuttersRecoil Know Your Snow ThrowerTo Throw Snow HOW to Move Forward and BackwardTo Stop Your Snow Thrower To Controlsnow DischargeFill GAS HOW to USE Wheel LockoutService & Adjustments section of this manual Before Starting the EngineTo Stop Engine To Start Engine Electric STARTER, if EquippedRecoil Starter Cold StartWarm Start To Start EngineFrozen Starter Snow Throwing Tips After Each USE Lubrication ChartCustomer Responsibilities General RecommendationsLubrication Every 10 Hours Product SpecificationsAS Required To Change Engine OIL EngineLUBRICATION-NOT Required LubricationWall maximum pressure on tire To Adjust Skid HeightTo Adjust Scraper BAR How To Adjust The Auger Drive Belt HOW to Check and Adjust the CablesTo Adjust Belts Traction Drive Belt How To Remove The Auger Drive BeltTo Replace Belts Tighten ,the nutTraction Belt Guide Drive Pulley Outdoors, away from fire orHow To Check The Friction Wheel HOW to Adjust or Replace the Friction WheelHOW to Adjust the Belt Guide Tighten nut on the speed control rod Protect the machine, use only HOW to Replace the Auger Shear BoltTighten the bottom bolts on each side of the bottom panel Important Never tamper with To Adjust the CarburetorTo Adjust or Replace the Spark Plug To adjustLine outdoors, away from Thoroughly clean the snow throwerSnow Thrower Screws,are securely fastened.Difficult starting 319042 Frame Assembly5359 DescriptionCraftsman 33 12.5HP Snow Thrower Electric Start AssemblyBottom Frame Assy192 Drive ComponentsRET E Drive ComponentsLever Key Auger Housing Assembly310 Gear Case AssemblyKey Description 306 340 321 327 330 304 316586 Discharge Chute Assembly6OO Craftsman 33 12.5HP Snow Thrower 536.881120 Handleassembly Key Part Description 678 673 Wheel Assembly768 Control Panel AssemblyKEY# REF. KEY# 337139 J 867863 864 866 874 Chute Control ROD Assembly856 855 854 855862 860Harness Headlight Headlight621 626 628 627 622 LIGHT, HalogenRemote Chute Control Assembly 968 965966 967280 Drift Cutter AssemblyCraftsman 4-CYCLE Engine Model Number Flywheel Key KEY Part Description10-32 x 3/4 Std180 35954 35187185 37085 Intake Pipe 35703 343 35079 Key Switch Bracket282 650760 Screw 342 792028 Screw, 5/16-18 285 35985B 33t25 Description KEY PartCraftsman 4-CYCLE Engine Model Number Cover KEY Part 81AR8

536.88112 specifications

The Craftsman 536.88112 is a powerful and versatile snow thrower designed to tackle heavy snowfall and provide effective cleaning solutions for residential properties. With a combination of robust build quality and innovative features, this machine stands out in the market for both performance and ease of use.

One of the main features of the Craftsman 536.88112 is its powerful gas engine, which delivers significant torque to efficiently clear snow from driveways, sidewalks, and other surfaces. With a clearing width of approximately 24 inches, this snow thrower can handle large volumes of snow quickly, saving users valuable time during winter storms. The adjustable chute can rotate up to 180 degrees, allowing for precise control over snow direction and ensuring that you can clear pathways without unnecessary rework.

The machine incorporates an easy-start technology that ensures reliable ignition in cold weather, making it user-friendly even in the harshest winter conditions. It also features a six-speed transmission, which allows users to adjust the speed according to their preferences and the density of the snow being cleared. This flexibility makes the Craftsman 536.88112 suitable for various snow types, from light and fluffy powder to heavier, dense accumulations.

Another notable characteristic of the Craftsman 536.88112 is its durable construction. Built with heavy-duty materials, the snow thrower is designed to withstand the rigors of tough winter conditions, ensuring longevity and reliable performance throughout the season. Furthermore, the ergonomic handle and control layout are designed for maximum comfort, making it easier for users to maneuver the machine over large areas.

Maintaining the Craftsman 536.88112 is also straightforward, with features that facilitate regular upkeep. The easy-access oil drain and refill points, coupled with industry-standard maintenance protocols, help ensure that the engine remains in prime condition for years to come.

In conclusion, the Craftsman 536.88112 snow thrower is a reliable and efficient solution for homeowners looking to manage winter snowfall effectively. With its powerful engine, adjustable chute, and robust design, it stands as an excellent investment for those who face harsh winter conditions, ensuring that pathways remain clear and safe throughout the season.
Top Page Image Contents