Craftsman 536.88112 To Adjust the Carburetor, To Adjust or Replace the Spark Plug, To adjust

Page 30

. Align the hole in the auger with the hole in the auger shaft. Install the new shear pin and spacer. See Figure 39.

4.Connect the spark plug wire.

Sh_earPin

_Figure 39

TO ADJUST THE CARBURETOR

If you think your carburetor needs ad- justing, see your nearest Sears Store. Engine performance should not be af- fected at altitudes up to 7,000 feet. For operation at higher elevations, contact your nearest,Sears Store.

IMPORTANT: Never tamper with the

engine governor, which is factory set for proper engine speed. Over-speeding the engine above the factory high speed setting can be dangerous. If you think the engine-governedhigh speed needs adjusting, contact your nearest

Sears Store, which has the proper equipment and experience to make any necessary adjustments.

TO ADJUST OR REPLACE THE SPARK PLUG

NOTE: This spark ignition system meets

all requirements of the Canadian Interfer-

ence-Causing Equipment Regulations,

If yOU have difficulty starting the snow thrower, adjust or replace the spark plug. Replace the spark plug is the electrodes are pitted or burned or if the porcelain is cracked. Follow the instruc- tions below.

To adjust:

1.Clean spark plug by carefully scraping the electrodes (Do not sand blast or use a wire brush).

2.Be sure spark plug is clean and free of foreign material. Check elec- trodes gap with a wire feeler gauge and reset gap to 0.030" if neces- sary. See Figure 40.

To Replace:

1.If you need a new spark plug, use only the proper replacement spark plug.

2.Set the gap to 0.030 inches.

3.Before installing the spark plug, lightly coat the spark plug threads

with oil or grease to insure easy re- moval.

. Firmly tighten the spark plug in the engine.

5.If a torque wrench is available, torque the plug to 18 to 23 foot pounds.

Feeler Gauge 0.030"

Spark Plug

Figure 40

F-O01129.130

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Snow Thrower 001129JLimited TWO-YEAR Warranty on Craftsman Snow Thrower Wash Hands After HandlingTraining PreparationMaintenance and Storage Control And Operating SymbolsWhen snow thrower is transported or not Never operate the snow thrower without÷61 Contents of Parts Bag actual size Parts packed separately in carton not shown full sizeLever How To Remove The Snow Thrower From The CartonTools Required DeflectorNot Universal Joint How To Install The KnobsKnob KnobHow To Install Speed Control Rod How To Assemble Chute DeflectorPin Drive Cable Short How To Set Length Of The CablesCheck The Cables TractionAuger Drive CableHow To Set The Drift Cutters ChecklistKnow Your Snow Thrower RecoilTo Controlsnow Discharge HOW to Move Forward and BackwardTo Stop Your Snow Thrower To Throw SnowBefore Starting the Engine HOW to USE Wheel LockoutService & Adjustments section of this manual Fill GASTo Start Engine Electric STARTER, if Equipped To Stop EngineTo Start Engine Cold StartWarm Start Recoil StarterFrozen Starter Snow Throwing Tips General Recommendations Lubrication ChartCustomer Responsibilities After Each USEProduct Specifications AS RequiredLubrication Every 10 Hours Lubrication EngineLUBRICATION-NOT Required To Change Engine OILTo Adjust Skid Height To Adjust Scraper BARWall maximum pressure on tire HOW to Check and Adjust the Cables To Adjust BeltsHow To Adjust The Auger Drive Belt Tighten ,the nut How To Remove The Auger Drive BeltTo Replace Belts Traction Drive BeltOutdoors, away from fire or Traction Belt Guide Drive PulleyHOW to Adjust or Replace the Friction Wheel HOW to Adjust the Belt GuideHow To Check The Friction Wheel Tighten nut on the speed control rod HOW to Replace the Auger Shear Bolt Tighten the bottom bolts on each side of the bottom panelProtect the machine, use only To adjust To Adjust the CarburetorTo Adjust or Replace the Spark Plug Important Never tamper withScrews,are securely fastened. Thoroughly clean the snow throwerSnow Thrower Line outdoors, away fromDifficult starting Description Frame Assembly5359 319042Electric Start Assembly Craftsman 33 12.5HP Snow ThrowerFrame Assy BottomDrive Components 192Drive Components LeverRET E Auger Housing Assembly Key306 340 321 327 330 304 316 Gear Case AssemblyKey Description 310Discharge Chute Assembly 5866OO Craftsman 33 12.5HP Snow Thrower 536.881120 Handleassembly Key Part Description Wheel Assembly 678 673Control Panel Assembly KEY# REF. KEY# 337139 J768 860 Chute Control ROD Assembly856 855 854 855862 867863 864 866 874LIGHT, Halogen Headlight621 626 628 627 622 Harness HeadlightRemote Chute Control Assembly 967 965966 968Drift Cutter Assembly 280Craftsman 4-CYCLE Engine Model Number Std KEY Part Description10-32 x 3/4 Flywheel Key35187 185 37085 Intake Pipe180 35954 343 35079 Key Switch Bracket 282 650760 Screw 342 792028 Screw, 5/16-18 285 35985B35703 33t25 KEY Part DescriptionCraftsman 4-CYCLE Engine Model Number Cover KEY Part 81AR8

536.88112 specifications

The Craftsman 536.88112 is a powerful and versatile snow thrower designed to tackle heavy snowfall and provide effective cleaning solutions for residential properties. With a combination of robust build quality and innovative features, this machine stands out in the market for both performance and ease of use.

One of the main features of the Craftsman 536.88112 is its powerful gas engine, which delivers significant torque to efficiently clear snow from driveways, sidewalks, and other surfaces. With a clearing width of approximately 24 inches, this snow thrower can handle large volumes of snow quickly, saving users valuable time during winter storms. The adjustable chute can rotate up to 180 degrees, allowing for precise control over snow direction and ensuring that you can clear pathways without unnecessary rework.

The machine incorporates an easy-start technology that ensures reliable ignition in cold weather, making it user-friendly even in the harshest winter conditions. It also features a six-speed transmission, which allows users to adjust the speed according to their preferences and the density of the snow being cleared. This flexibility makes the Craftsman 536.88112 suitable for various snow types, from light and fluffy powder to heavier, dense accumulations.

Another notable characteristic of the Craftsman 536.88112 is its durable construction. Built with heavy-duty materials, the snow thrower is designed to withstand the rigors of tough winter conditions, ensuring longevity and reliable performance throughout the season. Furthermore, the ergonomic handle and control layout are designed for maximum comfort, making it easier for users to maneuver the machine over large areas.

Maintaining the Craftsman 536.88112 is also straightforward, with features that facilitate regular upkeep. The easy-access oil drain and refill points, coupled with industry-standard maintenance protocols, help ensure that the engine remains in prime condition for years to come.

In conclusion, the Craftsman 536.88112 snow thrower is a reliable and efficient solution for homeowners looking to manage winter snowfall effectively. With its powerful engine, adjustable chute, and robust design, it stands as an excellent investment for those who face harsh winter conditions, ensuring that pathways remain clear and safe throughout the season.
Top Page Image Contents