Craftsman 536.88112 To Start Engine Electric STARTER, if Equipped, To Stop Engine

Page 16

WARNING: Experiences in-

,_ dicates that alcohol blended fuels (called gasohol or

those using ethanol or methanol) can attract moisture which leads to

separation and formation of acids during storage. Acidic gas can dam- age the fuel system of an engine while in storage.

NOTE: To avoid engine problems,

the fuel system must be emptied be- fore storage for 30 days or longer. Start the engine and let it run until the fuel lines and carburetor are empty. Use the carburetor bowl drain to empty residual gasoline from the float chamber. Use fresh

fuel next season. See the Storage section in'this manual for additional information.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

. Fill the fuel tank only with a fresh, clean, unleaded regular, unleaded premium, or reformulated automo- tive gasoline. DO NOT use leaded gasoline. Make sure that the con- tainer you pour the gasoline from is clean and free from rust or other for- eign particles. Never use gasoline that may be stale from long periods of storage in the container.

mable. Always use caution

,_ WARNING: Gasoline is flam- when handling or storing

gasoline.

Do not fill fuel tank while snow

thrower is running, when it is hot, or when snow thrower is in an en- closed area.

Keep away from open flame or an electrical spark and do not smoke while filling the fuel tank.

Never fill the tank completely. Fill the tank to within 1/4"-1/2" from the

top to provide space for expansion of fuel.

Always fill fuel tank outdoors and use a funnel or spout to prevent spilling.

Make sure to wipe up any spilled fuel before stating the engine. Store gasoline in a clean, approved

container and keep the cap in place on the container.

TO STOP ENGINE

To stop engine, move the throttle con- trol lever to "STOP" position and re- move key. Keep the key in a safe place. The engine will not start without the key.

TO START ENGINE

(ELECTRIC STARTER, IF EQUIPPED)

Be sure that the engine has sufficient oil. The snow throwerengine is equipped with a 120 volt A.C. electric

F--OO1129J16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Snow Thrower 001129JLimited TWO-YEAR Warranty on Craftsman Snow Thrower Wash Hands After HandlingTraining PreparationControl And Operating Symbols When snow thrower is transported or notMaintenance and Storage Never operate the snow thrower without÷61 Contents of Parts Bag actual size Parts packed separately in carton not shown full sizeHow To Remove The Snow Thrower From The Carton Tools RequiredLever DeflectorNot How To Install The Knobs KnobUniversal Joint KnobHow To Assemble Chute Deflector How To Install Speed Control RodPin How To Set Length Of The Cables Check The CablesDrive Cable Short TractionAuger Drive CableHow To Set The Drift Cutters ChecklistKnow Your Snow Thrower RecoilHOW to Move Forward and Backward To Stop Your Snow ThrowerTo Controlsnow Discharge To Throw SnowHOW to USE Wheel Lockout Service & Adjustments section of this manualBefore Starting the Engine Fill GASTo Start Engine Electric STARTER, if Equipped To Stop EngineCold Start Warm StartTo Start Engine Recoil StarterFrozen Starter Snow Throwing Tips Lubrication Chart Customer ResponsibilitiesGeneral Recommendations After Each USEAS Required Product SpecificationsLubrication Every 10 Hours Engine LUBRICATION-NOT RequiredLubrication To Change Engine OILTo Adjust Scraper BAR To Adjust Skid HeightWall maximum pressure on tire To Adjust Belts HOW to Check and Adjust the CablesHow To Adjust The Auger Drive Belt How To Remove The Auger Drive Belt To Replace BeltsTighten ,the nut Traction Drive BeltOutdoors, away from fire or Traction Belt Guide Drive PulleyHOW to Adjust the Belt Guide HOW to Adjust or Replace the Friction WheelHow To Check The Friction Wheel Tighten nut on the speed control rod Tighten the bottom bolts on each side of the bottom panel HOW to Replace the Auger Shear BoltProtect the machine, use only To Adjust the Carburetor To Adjust or Replace the Spark PlugTo adjust Important Never tamper withThoroughly clean the snow thrower Snow ThrowerScrews,are securely fastened. Line outdoors, away fromDifficult starting Frame Assembly 5359Description 319042Electric Start Assembly Craftsman 33 12.5HP Snow ThrowerFrame Assy BottomDrive Components 192Lever Drive ComponentsRET E Auger Housing Assembly KeyGear Case Assembly Key Description306 340 321 327 330 304 316 310Discharge Chute Assembly 5866OO Craftsman 33 12.5HP Snow Thrower 536.881120 Handleassembly Key Part Description Wheel Assembly 678 673KEY# REF. KEY# 337139 J Control Panel Assembly768 Chute Control ROD Assembly 856 855 854 855862860 867863 864 866 874Headlight 621 626 628 627 622LIGHT, Halogen Harness HeadlightRemote Chute Control Assembly 965 966967 968Drift Cutter Assembly 280Craftsman 4-CYCLE Engine Model Number KEY Part Description 10-32 x 3/4Std Flywheel Key185 37085 Intake Pipe 35187180 35954 282 650760 Screw 342 792028 Screw, 5/16-18 285 35985B 343 35079 Key Switch Bracket35703 33t25 KEY Part DescriptionCraftsman 4-CYCLE Engine Model Number Cover KEY Part 81AR8

536.88112 specifications

The Craftsman 536.88112 is a powerful and versatile snow thrower designed to tackle heavy snowfall and provide effective cleaning solutions for residential properties. With a combination of robust build quality and innovative features, this machine stands out in the market for both performance and ease of use.

One of the main features of the Craftsman 536.88112 is its powerful gas engine, which delivers significant torque to efficiently clear snow from driveways, sidewalks, and other surfaces. With a clearing width of approximately 24 inches, this snow thrower can handle large volumes of snow quickly, saving users valuable time during winter storms. The adjustable chute can rotate up to 180 degrees, allowing for precise control over snow direction and ensuring that you can clear pathways without unnecessary rework.

The machine incorporates an easy-start technology that ensures reliable ignition in cold weather, making it user-friendly even in the harshest winter conditions. It also features a six-speed transmission, which allows users to adjust the speed according to their preferences and the density of the snow being cleared. This flexibility makes the Craftsman 536.88112 suitable for various snow types, from light and fluffy powder to heavier, dense accumulations.

Another notable characteristic of the Craftsman 536.88112 is its durable construction. Built with heavy-duty materials, the snow thrower is designed to withstand the rigors of tough winter conditions, ensuring longevity and reliable performance throughout the season. Furthermore, the ergonomic handle and control layout are designed for maximum comfort, making it easier for users to maneuver the machine over large areas.

Maintaining the Craftsman 536.88112 is also straightforward, with features that facilitate regular upkeep. The easy-access oil drain and refill points, coupled with industry-standard maintenance protocols, help ensure that the engine remains in prime condition for years to come.

In conclusion, the Craftsman 536.88112 snow thrower is a reliable and efficient solution for homeowners looking to manage winter snowfall effectively. With its powerful engine, adjustable chute, and robust design, it stands as an excellent investment for those who face harsh winter conditions, ensuring that pathways remain clear and safe throughout the season.
Top Page Image Contents