Craftsman 536.88112 Control And Operating Symbols, When snow thrower is transported or not

Page 4

13.Never operate the snow thrower near en- closures, automobiles, window wells, drop-offs, and the like without proper ad- justment of the snow discharge angle. Keep children and pets away.

14.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

15.Never operate the machine at high trans- port speeds on slippery surfaces. Look be- hind and use care when backing up.

16.Never direct discharge at bystanders or allow anyone in front of the unit.

17.Disengage power to the collectodimpeller

when snow thrower is transported or not in

use.

18.Use only attachments and accessories ap- proved by the manufacturer of the snow thrower (such as tire chains, electric start kits, ect.).

19.Never operate the snow thrower without

good visibility or light. Always be sure of your footing and keep a firm hold on the handle_. Walk;never run.

20.Do not over-reach. Keep proper footing and balance at all times.

21.Do not attempt to use snow thrower on a roof.

MAINTENANCE AND STORAGE

1.Check shear belts and other belts at fre- quent intervals for proper tightness to be

sure the equipment is in safe working condition.

2.Never store the snow thrower with fuel in the tank inside a building where ignition sources are present such as hot water and space heaters, clothes dryers, and the like. Allow the engine (motor) to cool before storing in any enclosure.

3.Always refer to operator'sguide instruc- tions for important details if the snow thrower is to be stored for an extended

period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the snow thrower a few minutes after throwing snow to prevent freeze-upof the auger/impeller.

,_ WARNING:for use on sidewalks,This snow throwerdrivewaysis and other ground level surfaces.

Caution should be exercised while using on

steep sloping surfaces, DO NOT USE SNOW THROWER ON SURFACES ABOVE GROUND LEVEL such as roofs of resi- dences, garages, porches or other such structures or buildings.

IMPORTANT: Many of the following symbols are located on your unit or on literature sup-

plied with the product. Before you operate the unit, learn and understand the purpose for each symbol.

Control And Operating Symbols

Slow

Fast

Electric Start

Engine Start

Engine Run

I H N

Engine Off Engine Stop

On

Choke Off

Choke On

Neutral

®@

Throttle

Primer Button

Ignition Key

Ignition Off

Ignition On

F-001129J4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Snow Thrower 001129JLimited TWO-YEAR Warranty on Craftsman Snow Thrower Wash Hands After HandlingTraining PreparationControl And Operating Symbols When snow thrower is transported or notMaintenance and Storage Never operate the snow thrower without÷61 Contents of Parts Bag actual size Parts packed separately in carton not shown full sizeHow To Remove The Snow Thrower From The Carton Tools RequiredLever DeflectorNot How To Install The Knobs KnobUniversal Joint KnobHow To Assemble Chute Deflector How To Install Speed Control RodPin How To Set Length Of The Cables Check The CablesDrive Cable Short TractionAuger Drive CableHow To Set The Drift Cutters ChecklistKnow Your Snow Thrower RecoilHOW to Move Forward and Backward To Stop Your Snow ThrowerTo Controlsnow Discharge To Throw SnowHOW to USE Wheel Lockout Service & Adjustments section of this manualBefore Starting the Engine Fill GASTo Start Engine Electric STARTER, if Equipped To Stop EngineCold Start Warm StartTo Start Engine Recoil StarterFrozen Starter Snow Throwing Tips Lubrication Chart Customer ResponsibilitiesGeneral Recommendations After Each USEAS Required Product SpecificationsLubrication Every 10 Hours Engine LUBRICATION-NOT RequiredLubrication To Change Engine OILTo Adjust Scraper BAR To Adjust Skid HeightWall maximum pressure on tire To Adjust Belts HOW to Check and Adjust the CablesHow To Adjust The Auger Drive Belt How To Remove The Auger Drive Belt To Replace BeltsTighten ,the nut Traction Drive BeltOutdoors, away from fire or Traction Belt Guide Drive PulleyHOW to Adjust the Belt Guide HOW to Adjust or Replace the Friction WheelHow To Check The Friction Wheel Tighten nut on the speed control rod Tighten the bottom bolts on each side of the bottom panel HOW to Replace the Auger Shear BoltProtect the machine, use only To Adjust the Carburetor To Adjust or Replace the Spark PlugTo adjust Important Never tamper withThoroughly clean the snow thrower Snow ThrowerScrews,are securely fastened. Line outdoors, away fromDifficult starting Frame Assembly 5359Description 319042Electric Start Assembly Craftsman 33 12.5HP Snow ThrowerFrame Assy BottomDrive Components 192Lever Drive ComponentsRET E Auger Housing Assembly KeyGear Case Assembly Key Description306 340 321 327 330 304 316 310Discharge Chute Assembly 5866OO Craftsman 33 12.5HP Snow Thrower 536.881120 Handleassembly Key Part Description Wheel Assembly 678 673KEY# REF. KEY# 337139 J Control Panel Assembly768 Chute Control ROD Assembly 856 855 854 855862860 867863 864 866 874Headlight 621 626 628 627 622LIGHT, Halogen Harness HeadlightRemote Chute Control Assembly 965 966967 968Drift Cutter Assembly 280Craftsman 4-CYCLE Engine Model Number KEY Part Description 10-32 x 3/4Std Flywheel Key185 37085 Intake Pipe 35187180 35954 282 650760 Screw 342 792028 Screw, 5/16-18 285 35985B 343 35079 Key Switch Bracket35703 33t25 KEY Part DescriptionCraftsman 4-CYCLE Engine Model Number Cover KEY Part 81AR8

536.88112 specifications

The Craftsman 536.88112 is a powerful and versatile snow thrower designed to tackle heavy snowfall and provide effective cleaning solutions for residential properties. With a combination of robust build quality and innovative features, this machine stands out in the market for both performance and ease of use.

One of the main features of the Craftsman 536.88112 is its powerful gas engine, which delivers significant torque to efficiently clear snow from driveways, sidewalks, and other surfaces. With a clearing width of approximately 24 inches, this snow thrower can handle large volumes of snow quickly, saving users valuable time during winter storms. The adjustable chute can rotate up to 180 degrees, allowing for precise control over snow direction and ensuring that you can clear pathways without unnecessary rework.

The machine incorporates an easy-start technology that ensures reliable ignition in cold weather, making it user-friendly even in the harshest winter conditions. It also features a six-speed transmission, which allows users to adjust the speed according to their preferences and the density of the snow being cleared. This flexibility makes the Craftsman 536.88112 suitable for various snow types, from light and fluffy powder to heavier, dense accumulations.

Another notable characteristic of the Craftsman 536.88112 is its durable construction. Built with heavy-duty materials, the snow thrower is designed to withstand the rigors of tough winter conditions, ensuring longevity and reliable performance throughout the season. Furthermore, the ergonomic handle and control layout are designed for maximum comfort, making it easier for users to maneuver the machine over large areas.

Maintaining the Craftsman 536.88112 is also straightforward, with features that facilitate regular upkeep. The easy-access oil drain and refill points, coupled with industry-standard maintenance protocols, help ensure that the engine remains in prime condition for years to come.

In conclusion, the Craftsman 536.88112 snow thrower is a reliable and efficient solution for homeowners looking to manage winter snowfall effectively. With its powerful engine, adjustable chute, and robust design, it stands as an excellent investment for those who face harsh winter conditions, ensuring that pathways remain clear and safe throughout the season.
Top Page Image Contents