Craftsman 247.88854 owner manual Attaching Turn Triggers, Lamp Wiring

Page 10

•Secure the ferrule to the shift lever with another 5/16 flat washer and hairpin clip from group D of the hardware pack. See Figure 11.

•Make certain to check for correct adjustment of the shift rod as instructed in the Adjustment section before operating the snow thrower.

Attaching Turn Triggers

•Check and make sure that the right hand trigger cable is routed in front of the traction drive cable.

•Feed the trigger cable up through the outer side of the slot in the handle panel. See Figure 12. Do not feed the cable through the same side of the slot as the Z fitting.

Cable

Feed the trigger cable through this slot

Figure 12

•Place the cable barrel fitting into the hole in the trigger. You can find the triggers and associated hardware in group H of the hardware pack. See Figure 13.

Trigger

Assembly

Inner Cable

Trigger

 

Cable

Housing

 

Barrel

 

 

Slot

Fitting

 

Cable snaps in at

 

 

this end

Figure 13

•

Pull on the cable and rotate it around the bottom

 

of the trigger, with the inner cable in the slot, until

and weld nut from group H of the hardware pack. See Figure 14. Use a phillips screwdriver for tightening the screw. Repeat on left side. Be careful not to drop the weld nut before securing it in position.

Secure with screw

Weld Nut

Turn

Trigger

Slot

Trigger Cable

 

Figure 14

•Secure the right turn trigger cable to the right lower handle using cable tie provided in the hardware pack. Make sure not to wrap the drive cable. See Figure 15.

Trigger Cable

Cable Tie

Figure 15

•Secure the left turn trigger cable to the lower handle using the other cable tie. Make sure to route the cable tie below the auger drive cable so that when the trigger cable is secured by the cable tie, the auger drive cable is left outside the cable tie. Trim excess ends from each cable tie.

NOTE: The right side cable tie must be used to keep cable from coming in contact with the moving shift arm from the transmission.

Lamp Wiring

•Wrap the wire from the lamp down the right handle as shown in Figure 15.

•Plug wire into the alternator lead wire under the fuel tank. See Figure 16.

Alternator Lead

the cable end can be pushed into the trigger

housing and snapped tight. See Figure 13.

NOTE: When the cable is installed correctly, you should not be able to pull the cable out of the trigger housing.

•Place the right turn trigger in position underneath the right handle. Secure with screw

Lamp Wire

(Wheels not shown for clarity)

Figure 16

Alternator

Lead

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 247.888540 Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.ATable of Contents Warranty InformationSafe Operation Practices TrainingMaintenance and Storage Hardware Pack Removing From Carton AssemblyAttaching Handle Assembly Loose PartsHandle Tab Attaching ChuteChute Hex Hex Bolt Flange Nut Keeper Attaching Chute Crank On the left side of the handle panel, placeCable Guide Attaching Clutch CablesAttaching Shift Rod Outer side Fitting Slot Hex Jam Nut Flats Ferrule BarrelLamp Wiring Attaching Turn TriggersTraction Drive Clutch and Shift Lever Final AdjustmentsAuger Control Skid ShoeOperation Meets Ansi Safety StandardsKnowing Your Snow Thrower Stopping Snow Thrower Operating ControlsBefore Starting Engine Electric Starter To Start EngineStarting Instructions At a Glance Cold StartOperating Snow Thrower To Throw SnowTo Stop The Snow Thrower Before StoppingOperating Tips Lubrication MaintenanceGeneral Recommendations Customer ResponsibilitiesCheck V-belts Engine MaintenanceCheck Friction Wheel Changing Oil Viscosity ChartChecking Oil Level Spark PlugService & Adjustments AdjustmentsAugers ServiceCarburetor Shave Plate and Skid ShoesChute Hairpin Clip Crank Frame Assembly Auger HousingHex Nut Lock Washer Friction Wheel Idler Pulley Location Drive Belt Disc Drive BeltChanging Friction Wheel Rubber Drive CoverCarburetor Shift Arm Assembly Sprocket Spacer Pin Friction WheelSprocket Spacer Hex Shaft Hex Hub Preparing Snow Thrower OFF-SEASON StoragePreparing Engine Carburetor Bowl DrainTROUBLE-SHOOTING Trouble Possible Causes Corrective ActionSnow Thrower Safety and Decorative Labels Map Repair Parts Sears Craftsman 9.0 H.P. Snow Thrower Model 23358 Sears Craftsman 9.0 H.P. Snow Thrower Model 19 40 72 57 Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower 298 130B 301 396 340 300 264A 400 310 Key Part Description Qty Recoil Starter Carburetor Especificaciones Del Producto Garantia DE InformaciónNumero De Modelo Practicas Seguras DE Operacion EntrenamientoMantenimiento Y Almacenamiento Conjunto DE Ferreteria DE Ferreteria Piezas de RepuestoPiezas Sueltas EnsambladoExtraccion De La Unidad De La Caja Herramientas RequeridasFijacion De La Canaleta Fijacion De La Manivela De La CanaletaPerno del carro, contratuerca hexagonal Arandela plana Soporte de la manija Inferior de la canaletaFijacion De La Vara De Cambios Fijacion De Los Cables Del EmbragueFijacion De Los Gatillos De Giro Cableado de la LámparaAjuste de la Zapata Deslizante Ajustes FinalesPresion De La Ruedas Ajuste del Control de la HéliceOperacion Palanca De CambiosConozca Su Expulsor De Nieve Figura Arrancador Eléctrico Detencion Del Expulsor De NieveLlenado De Gasolina Y Aceite Arranque Del MotorPara Enganchar El Propulsor Como Apagar El MotorEnganche De La Propulsion Enganche De Las Espirales Sin Fin Consejos De OperacionManejo De La Limpiadora De Nieve Instrucciones Abreviadas de ArranqueRecomendaciones Generales MantenimientoLubricación Inspección de las correas en Inspección de la rueda de fricciónTabla de la Viscosidad Mantenimiento del MotorAceite De Motor Cambio de aceiteService & Ajustes AjustesReemplazo De La Correa ServiceHelices Correas de la espiral sin finNota Sea precavido para evitar apretar el cable de control Correa propulsora PlanchaPinon Separador Eje Hexagonal Cubo hexagonal del pinon Preparación del motor Almacenamiento DE Fuera DE TemporadaPreparación del Expulsor de Nieve Problema Causas posible Accion correctora Tabla DE Localizacion DE FallasTo purchase or inquire about a Sears Maintenance Agreement U.S.A. or Canada For in-home major brand repair serviceFor the repair or replacement parts you need Para pedir servicio de reparación a domicillio
Top Page Image Contents