Husqvarna 1130SB-XLS owner manual KEY Part Description

Page 21

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 1130SB-XLS(96193003000), PRODUCT NO. 961 93 00-30

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 18 41-05	IMPELLER
2	532 19 67-10 GEARBOX ASSEMBLY
3	532 18 89-09	BEARING

4532 19 10-79 IMPELLER PULLEY

5532 17 53-22 DISCHARGE BASE

6532 18 40-95 CORNER BRACKET

7532 19 21-99 CLEAN OUT TOOL

8	532 40 54-00	TOOL CLIP
9	873 80 04-00	NUT 1/4−20
10	874 78 04-26 SCREW 1/4−20 X .625
11	532 15 53-77	NUT 5/16−18
12	532 16 31-83 SCREW 5/16−18 X .625
13	819 11 15-07	WASHER

14810 04 05-00 LOCKWASHER 5/16

15874 94 05-16 SCREW 5/16−18 X 1.00

16532 18 03-55 CARRIAGE BOLT

17532 19 41-89 SCREW 13−16 X .625

18	532 40 77-60	PLUG
19	532 40 77-61 GEARBOX COVER RH
20	532 40 77-66	GASKET
21	532 40 77-70	SEAL
22	532 40 77-62	BEARING
23	532 17 46-97 THRUST WASHER 1.00
24	532 40 77-63	WORM GEAR
25	532 40 77-64	AUGER SHAFT
26	532 18 92-82	SQUARE KEY
27	532 40 77-58	BEARING

28532 17 46-83 THRUST WASHER

29532 40 77-57 IMPELLER SHAFT

30	532 18 42-05 ROLL PIN

31532 17 46-81 THRUST WASHER

32532 17 46-84 THRUST BEARING

33	532 40 77-69	BEARING
34	532 40 77-68	O−RING

35532 40 77-67 SCREW 5/16−18 X .750

36532 40 77-65 GEARBOX COVER LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21

Image 21

Contents 1130SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationCleaning Snow ThrowerEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingWeight BAR CARRIAGEBOLT5/16−18X.750CARRIAGEBOLT5/16−18X1.25 Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer StrapCable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-B 532 42 13-51 Console Panel Gray Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightAxle Shaft DriveThrust Washer Clik PIN92122 532 18 77-86 Traction Idler ARM 532 18 04-78 Engine Traction PulleyIdler Pulley Clevis PIN01.01.001-B Frame Tecumseh EngineBottom PAN Impeller BeltWheels Wheel Assembly LHSteer Cable Bracket LH Steer Cable Bracket RHWheel Lobe CoverSpring Axle LobeKEY Part Description 532 03 50-62 Safety Ignition KEY Power CordBAG of Parts Retainer PIN532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement