Husqvarna 1130SB-XLS owner manual BAG of Parts, Power Cord, Retainer PIN, Wrench

Page 38

REPAIR PARTS

BAG OF PARTS

SNOW THROWER - MODEL NO. 1130SB-XLS(96193003000), PRODUCT NO. 961 93 00-30

4

 

 

5

6

7

 

 

8

9

 

3

10 11

2

1

14

 

13

 

 

 

12

01.14.003-A

KEY

PART

DESCRIPTION

NO.

NO.

1

532 19 85-63

POWER CORD

2

532 16 96-75

RETAINER PIN

3

532 18 06-84

WRENCH

4532 18 45-05 REMOTE SPRING

5532 17 98-29 SHOULDER BOLT 1/4−20

6532 17 92-46 NYLON WASHER 1/4−20

7532 19 17-30 LOCKNUT 1/4−20

8872 25 05-05 CARRIAGE BOLT 5/16−18 X 5/8

9532 75 11-53 LOCKNUT 5/16−18

10873 80 06-00 LOCKNUT 3/8−16

11

819 13 13-16

WASHER 3/8

12

532 19 86-36

SHEAR BOLT 1/4−20 X 1−3/4

13

532 19 86-38

SPACER

14

873 80 04-00

LOCKNUT 1/4−20

1

KEY

PART

DESCRIPTION

NO.

NO.

1

532 03 50-62 SAFETY IGNITION KEY

01.14.008-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents 1130SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationEngine CleaningSnow Thrower Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Assembly 30 LH Auger Assembly 30 RHAuger Ball Bearing Skid PlateCARRIAGEBOLT5/16−18X1.25 Weight BARCARRIAGEBOLT5/16−18X.750 POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-B 532 42 14-48 Headlight Bezel Gray Grip Switch532 42 13-51 Console Panel Gray 532 17 86-66 Halogen HeadlightThrust Washer DriveAxle Shaft Clik PIN92122 Idler Pulley 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Clevis PIN01.01.001-B Bottom PAN Tecumseh EngineFrame Impeller BeltSteer Cable Bracket LH Wheel Assembly LHWheels Steer Cable Bracket RHSpring CoverWheel Lobe Axle LobeBAG of Parts Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY Retainer PINDecals 532 18 10-35 DECAL, DANGER, DeflectorWarranty Statement
Top Page Image Contents