Husqvarna 1130SB-XLS owner manual Washer, POP Rivet 1/8

Page 28

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 1130SB-XLS(96193003000), PRODUCT NO. 961 93 00-30

			10
				1
		5	6
10			6
10
		8		7
		2
5	8		3	9
5			3

	6		7
	8
	4	9
	4

01.08.011-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 42 17-08 PLOW HANDLE LH

2532 42 17-09 PLOW HANDLE RH

3532 19 69-44 PANEL BRACKET LH

4532 19 69-43 PANEL BRACKET RH

5532 41 45-15 HEATED HANDLE GRIP

6874 78 05-12 SCREW 5/16−18 X .750

7874 78 05-24 SCREW 5/16−18 X 1.50

8	532 75 11-53	NUT 5/16−18
9	532 15 54-15	WASHER
10	532 17 87-75	POP RIVET 1/8

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	532 42 17-05 LOWER TUBE GRAY
	2	532 40 76-43 PIVOT SUPPORT
	3	532 15 00-78	BOLT 5/16−18 X .75
2	4	817 00 06-16	SCREW 3/8−16 X 1.00

4 01.05.006-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 28

Image 28

Contents 1130SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonAssembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationSnow Thrower CleaningEngine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Assembly 30 LH Auger Assembly 30 RHAuger Ball Bearing Skid PlateCARRIAGEBOLT5/16−18X.750 Weight BARCARRIAGEBOLT5/16−18X1.25 Control Panel / Discharge Chute Knob BlackPOP Rivet 532 42 17-28 Shield Retainer Strap532 42 11-60 LEVER/CABLE Rotator Assembly Gray Cable Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-B Grip Switch 532 42 13-51 Console Panel Gray532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightDrive Axle ShaftThrust Washer Clik PIN92122 532 18 04-78 Engine Traction Pulley 532 18 77-86 Traction Idler ARMIdler Pulley Clevis PIN01.01.001-B Tecumseh Engine FrameBottom PAN Impeller BeltWheel Assembly LH WheelsSteer Cable Bracket LH Steer Cable Bracket RHCover Wheel LobeSpring Axle LobePower Cord KEY Part Description 532 03 50-62 Safety Ignition KEYBAG of Parts Retainer PINDecals 532 18 10-35 DECAL, DANGER, DeflectorWarranty Statement

REPAIR PARTS

HANDLES

KEY

WASHER

POP RIVET 1/8

KEY