Husqvarna 1130SB-XLS owner manual Install Traction Drive Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into eye of cable with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP

OPENING

DOWN

CABLE

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

6

Image 6

Contents 1130SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Assembly 30 LH Auger Assembly 30 RHAuger Ball Bearing Skid PlateWeight BAR CARRIAGEBOLT5/16−18X.750CARRIAGEBOLT5/16−18X1.25 POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-B 532 42 14-48 Headlight Bezel Gray Grip Switch532 42 13-51 Console Panel Gray 532 17 86-66 Halogen HeadlightThrust Washer DriveAxle Shaft Clik PIN92122 Idler Pulley 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Clevis PIN01.01.001-B Bottom PAN Tecumseh EngineFrame Impeller BeltSteer Cable Bracket LH Wheel Assembly LHWheels Steer Cable Bracket RHSpring CoverWheel Lobe Axle LobeBAG of Parts Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY Retainer PINDecals 532 18 10-35 DECAL, DANGER, DeflectorWarranty Statement