Husqvarna 1130SB-XLS owner manual Cover, Wheel Lobe, Spring, Axle Lobe, Lever PIN

Page 37

REPAIR PARTS

WHEELS

SNOW THROWER - MODEL NO. 1130SB-XLS(96193003000), PRODUCT NO. 961 93 00-30

2

									17		23
						20					23
						20				19
				17	18	16					22	7
						15	18				22	7
						15	18				9	8
				16		24					10
				20		23		21			11
				19		22
				19							12
				21							12
											14
								14 13			13
						11		14 13
					10			12
2				8	9
2				7
	3	4	5	6
2	1 01.15.001-A
				KEY	PART				DESCRIPTION
				NO.	NO.				DESCRIPTION
				1	532 40 51-61					COVER

2532 18 44-71 SHOULDER SCREW

3812 00 00-45 RETAINER RING

4532 19 21-26 WHEEL DRIVER

5532 18 24-66 RETAINER RING

6	532 18 76-22	WHEEL LOBE
7	532 19 49-41 CLUTCH SLIDE
8	532 17 91-39	SPRING
9	532 18 92-82	SQUARE KEY
10	532 19 49-40	AXLE LOBE

11532 17 46-97 THRUST WASHER

12532 19 95-19 STEERING YOKE

13532 18 41-97 STEERING BRACKET

14817 49 05-08 SCREW 5/16−18 X .50

15532 19 95-11 PIVOT BRACKET

16	532 19 95-18 BELLCRANK

17532 18 18-47 BELLCRANK PIN

18817 60 04-06 SCREW 1/4−20 X .375

19532 40 50-77 STEERING LINK

20	532 70 02-79	RETAINER
21	532 08 51-79	RETAINER
22	532 19 38-85	SPRING
23	532 18 20-15	LEVER PIN
24	532 19 95-12 PIVOT BRACKET

		3	2
	4	3	1
6	5

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

37

Image 37

Contents 1130SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationSnow Thrower CleaningEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingCARRIAGEBOLT5/16−18X.750 Weight BARCARRIAGEBOLT5/16−18X1.25 Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer StrapCable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-B 532 42 13-51 Console Panel Gray Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightAxle Shaft DriveThrust Washer Clik PIN92122 532 18 77-86 Traction Idler ARM 532 18 04-78 Engine Traction PulleyIdler Pulley Clevis PIN01.01.001-B Frame Tecumseh EngineBottom PAN Impeller BeltWheels Wheel Assembly LHSteer Cable Bracket LH Steer Cable Bracket RHWheel Lobe CoverSpring Axle LobeKEY Part Description 532 03 50-62 Safety Ignition KEY Power CordBAG of Parts Retainer PIN532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement