Husqvarna 1130SB-XLS owner manual Meets A.N.S.I. Safety Requirements

Page 9

OPERATION

SPARK	ENGINE OIL CAP	AUGER
PLUG	WITH DIPSTICK	CONTROL

DISCHARGE CHUTE CONTROL LEVER

	SAFETY			LEVER
	IGNITION
	KEY			GASOLINE
				GASOLINE
				FILLER
				CAP
	CHOKE			CHUTE
	CHOKE			DEFLECTOR
	CON-			DEFLECTOR
	TROL
				FUEL
				SHUT-OFF
				VALVE
	THROTTLE
	/ ENGINE
	CONTROL			DISCHARGE
				DISCHARGE
				CHUTE
	RECOIL	POWER
	(AUXILIARY)	POWER
	(AUXILIARY)	CORD
	STARTER	CORD
	STARTER	PLUG	ELECTRIC
	HANDLE	PLUG		OIL DRAIN PLUG
	HANDLE			OIL DRAIN PLUG
			START
			BUTTON	CLEAN-OUT TOOL
	PRIMER
	NOTE: ITEMS ABOVE
	ARE SHOWN IN
	THEIR TYPICAL
	LOCATION ON THE
	ENGINE. ACTUAL
	LOCATION MAY VARY
	WITH THE ENGINE
	ON YOUR UNIT.

DRIVE SPEED	DEFLECTOR
CONTROL LEVER	REMOTE
	CONTROL
	LEVER

TRACTION

DRIVE

CONTROL

LEVER

LH TURN TRIGGER

LIGHT

HANDLE

KNOB

MUFFLER

TOOLBOX

FREEWHEEL CONTROL

DRIFT

CUTTER

AUGERS

FIG. 10

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke Control - used for starting a cold engine.

Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.

LH and RH turn triggers - used to steer the snow thrower.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Deflector remote control lever - used to change the distance the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

9 Drift cutter - used to cut through deep snowdrifts.

Image 9

Contents 1130SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationCleaning Snow ThrowerEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingWeight BAR CARRIAGEBOLT5/16−18X.750CARRIAGEBOLT5/16−18X1.25 Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer StrapCable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-B 532 42 13-51 Console Panel Gray Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightAxle Shaft DriveThrust Washer Clik PIN92122 532 18 77-86 Traction Idler ARM 532 18 04-78 Engine Traction PulleyIdler Pulley Clevis PIN01.01.001-B Frame Tecumseh EngineBottom PAN Impeller BeltWheels Wheel Assembly LHSteer Cable Bracket LH Steer Cable Bracket RHWheel Lobe CoverSpring Axle LobeKEY Part Description 532 03 50-62 Safety Ignition KEY Power CordBAG of Parts Retainer PIN532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement