Husqvarna 1130SB-XLS 532 18 04-78 Engine Traction Pulley, 532 18 77-86 Traction Idler ARM, Pin

Page 33

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 1130SB-XLS(96193003000), PRODUCT NO. 961 93 00-30

KEY	PART	DESCRIPTION	KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION
1	532 19 20-02 SHIFT BRACKET		27	532 05 92-89	WASHER
2	817 50 10-10 SCREW 10−24 X .625		28	810 04 05-00 LOCKWASHER 5/16
3	874 76 05-52 SCREW 5/16−18 X 3.25		29	874 61 05-16 SCREW 5/16−18 X 1.00
4	532 17 92-46 PLASTIC WASHER		30	532 40 94-75	SPACER
5	532 19 20-01 SHIFT ASSEMBLY		31	532 18 04-78 ENGINE TRACTION PULLEY
6	532 15 54-15	WASHER	32	532 40 00-26	WASHER
7	532 19 21-95 FRICTION SPRING		33	532 85 02-63 LOCKWASHER 3/8
8	873 80 05-00	NUT 5/16−18	34	532 85 10-84 SCREW 3/8−24 X 1.38
9	817 49 05-08 BOLT 5/16−18 X .500		35	532 18 77-86 TRACTION IDLER ARM
10	532 40 54-84 CONTROL ARM		36	532 18 05-22	IDLER PULLEY
11	532 40 61-09 CONTROL SHAFT		37	874 78 05-20 SCREW 5/16−18 X 1.25
12	532 05 70-79	WASHER	38	873 93 05-00	NUT 5/16−18
13	532 19 85-80	CLEVIS PIN	39	874 78 05-24 SCREW 5/16−18 X 1.50
14	532 40 78-68	REAR PLATE	40	532 17 53-30	PIN
15	532 18 77-76	TRANSMISSION	41	532 40 78-49 IDLER PIVOT BRACKET
16	532 19 32-56	ROD	42	532 42 21-11 IDLER BRAKE ARM
17	532 19 20-00 REAR CABLE BRACKET		43	532 08 51-79	RETAINER
18	532 18 77-87 CONTROL ARM		44	532 17 88-28 BRAKE SPRING
19	532 19 19-93 FRONT CABLE BRACKET		45	532 16 67-85	NUT 5/16−18
20	532 15 00-78 SCREW 5/16−18 X .750		46	532 18 05-23	PULLEY
21	532 08 79-30	CLIP	47	873 80 04-00	NUT 1/4−20
22	817 39 12-08 SCREW .12 X .50		48	532 19 19-95 POP RIVET 1/4 X .475
23	532 17 53-31	BUSHING	49	532 19 84-66 CLUTCH CABLE
24	532 19 36-07	BELT GUIDE	50	532 19 28-73 TRACTION SPRING
25	811 05 05-00 LOCKWASHER 5/16		51	532 70 02-79 RETAINER CLIP
26	817 49 04-08 SCREW 1/4−20 X .500

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 33

Image 33

Contents 1130SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationCleaning Snow ThrowerEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingWeight BAR CARRIAGEBOLT5/16−18X.750CARRIAGEBOLT5/16−18X1.25 Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer StrapCable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-B 532 42 13-51 Console Panel Gray Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightAxle Shaft DriveThrust Washer Clik PIN92122 532 18 77-86 Traction Idler ARM 532 18 04-78 Engine Traction PulleyIdler Pulley Clevis PIN01.01.001-B Frame Tecumseh EngineBottom PAN Impeller BeltWheels Wheel Assembly LHSteer Cable Bracket LH Steer Cable Bracket RHWheel Lobe CoverSpring Axle LobeKEY Part Description 532 03 50-62 Safety Ignition KEY Power CordBAG of Parts Retainer PIN532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement