Husqvarna 1130SB-XLS owner manual Tecumseh Engine, Frame, Bottom PAN, Impeller Belt

Page 35

REPAIR PARTSCHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 1130SB-XLS(96193003000), PRODUCT NO. 961 93 00-30

1	3

			KEY	PART	DESCRIPTION
			NO.	NO.	DESCRIPTION
			- -	- - - - - -	TECUMSEH ENGINE
					OH318SA-221835B
4			1	532 41 61-55	FRAME
			2	532 40 37-32	BOTTOM PAN
			3	532 15 04-06	BOLT 3/8−16
	2	01.00.023-A	4	532 18 44-71 SCREW 10−24 X .625
		01.00.023-A

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	532 40 91-61 COVER ASSEMBLY
2	2	532 17 88-13	PULLEY
2	3	532 18 77-88 TRACTION BELT
	3	532 18 77-88 TRACTION BELT
	4	532 40 80-08	IMPELLER BELT

01.04.006

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 35

Contents 1130SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigBefore Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningSnow Thrower Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingCARRIAGEBOLT5/16−18X1.25 Weight BARCARRIAGEBOLT5/16−18X.750 532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP RivetRotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator HeadHandles POP Rivet 1/8 01.12.002-B 532 17 86-66 Halogen Headlight Grip Switch532 42 13-51 Console Panel Gray 532 42 14-48 Headlight Bezel GrayClik PIN DriveAxle Shaft Thrust Washer92122 Clevis PIN 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Idler Pulley01.01.001-B Impeller Belt Tecumseh EngineFrame Bottom PANSteer Cable Bracket RH Wheel Assembly LHWheels Steer Cable Bracket LHAxle Lobe CoverWheel Lobe SpringRetainer PIN Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY BAG of Parts532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement

REPAIR PARTSCHASSIS / ENGINE / PULLEYS

KEY

TECUMSEH ENGINE

FRAME

BOTTOM PAN

KEY

PULLEY

IMPELLER BELT