Husqvarna 1130SB-XLS owner manual Auger Assembly 30 LH, Auger Assembly 30 RH

Page 22

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 1130SB-XLS(96193003000), PRODUCT NO. 961 93 00-30

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	532 42 17-13 AUGER HOUSING
	2	532 40 76-45 SCRAPPER BAR
3 (5x)	3	872 27 05-05	CARRIAGE BOLT 5/16−18 X .625
3 (5x)	4	532 15 53-77	NUT 5/16−18
	4	532 15 53-77	NUT 5/16−18

4 (5x)

01.07.023-B

1	KEY	PART
1	NO.	NO.	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	532 42 17-26	AUGER ASSEMBLY 30 LH
	2	532 42 17-27	AUGER ASSEMBLY 30 RH

01.07.016-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 22

Contents 1130SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationSnow Thrower CleaningEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Assembly 30 LH Auger Assembly 30 RHAuger Ball Bearing Skid PlateCARRIAGEBOLT5/16−18X.750 Weight BARCARRIAGEBOLT5/16−18X1.25 POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-B 532 42 14-48 Headlight Bezel Gray Grip Switch532 42 13-51 Console Panel Gray 532 17 86-66 Halogen HeadlightThrust Washer DriveAxle Shaft Clik PIN92122 Idler Pulley 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Clevis PIN01.01.001-B Bottom PAN Tecumseh EngineFrame Impeller BeltSteer Cable Bracket LH Wheel Assembly LHWheels Steer Cable Bracket RHSpring CoverWheel Lobe Axle LobeBAG of Parts Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY Retainer PINDecals 532 18 10-35 DECAL, DANGER, DeflectorWarranty Statement

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

KEY

KEY

AUGER ASSEMBLY 30 LH

AUGER ASSEMBLY 30 RH