Husqvarna 1130SB-XLS owner manual Drive, Axle Shaft, Thrust Washer, Clik PIN

Page 31

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 1130SB-XLS(96193003000), PRODUCT NO. 961 93 00-30

6

	7
		4
8	2	3
8	2
7	1
	1
	9

2

	5	3
	5	4
		4

601.03.003-A

KEY	PART		DESCRIPTION
NO.	NO.		DESCRIPTION
1	532	40 43-08	AXLE SHAFT
2	532	18 77-94	SPACER
3	532	17 46-97	THRUST WASHER
4	532	17 98-30	BEARING

5532 14 63-15 SCREW 5/16−18 X .625

6817 49 05-08 BOLT 5/16−18 X .500

7	532 15 54-43	CLIK PIN
8	874 78 06-32	SCREW 3/8−16 X 2.00
9	873 80 06-00	NUT 3/8−16

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 31

Image 31

Contents 1130SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigBefore Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USESnow Thrower CleaningEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingCARRIAGEBOLT5/16−18X.750 Weight BARCARRIAGEBOLT5/16−18X1.25 532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP RivetRotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator HeadHandles POP Rivet 1/8 01.12.002-B 532 17 86-66 Halogen Headlight Grip Switch532 42 13-51 Console Panel Gray 532 42 14-48 Headlight Bezel GrayClik PIN DriveAxle Shaft Thrust Washer92122 Clevis PIN 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Idler Pulley01.01.001-B Impeller Belt Tecumseh EngineFrame Bottom PANSteer Cable Bracket RH Wheel Assembly LHWheels Steer Cable Bracket LHAxle Lobe CoverWheel Lobe SpringRetainer PIN Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY BAG of Parts532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement