ViewSonic PJ400 manual Connecting your devices, About Plug-and-Play capability

Page 17

Connecting your devices

CAUTION ►Turn off all devices prior to connecting them to the projector. Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector.

►Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause a certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector.

►Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector.

NOTE • Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer.

•Secure the screws on the connectors and tighten.

•Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

•For some RGB signal modes, the optional Mac adapter is necessary.

•When the image resolution is changed on a computer, depending on an input, automatic adjust function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution.

About Plug-and-Play capability

Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC 2B. Plug-and-Play can be achieved by connecting this projector to computers that are VESA DDC (display data channel) compatible.

•Please take advantage of this function by connecting the accessory RGB cable to the RGB port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

•Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor.

ViewSonic PJ400

13

Page 16 Page 18
Image 17
Page 16 Page 18
Contents PJ400 LCD Projector Compliance Information Important Safety Instructions Copyright Information Trademark acknowledgment PJ400 Model No.VS10459About this manual Contents About contents of package Projector featuresProjector Part namesMagnify Remote controlControls Fastening the lens cover PreparationsPutting batteries Using the remote control About the filter cover for bottom-up use Setting up At 43 screen ArrangementAdjusting the projectors elevator About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting power supply Turning on the power Power on/offTurning off the power Selecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom magnifying power Searching an input signalAdjusting the focus Selecting an aspect ratioAt a video signal Using the automatic adjustment featureAdjusting the position Correcting the keystone distortionsTemporarily blanking the screen Using the partial magnify featureFreezing the screen Using the menu function Multifunctional settingTo display a menu To choose the target menuTo choose the target item To reset Setup MenuTo operate To return to the previous menuZoom AspectKeystone ModeWhisper ResetMirror Filter TimePicture menu To adjust #1 CUSTOM, #2 Custom or #3 CustomUsing a test pattern High Middle Custom LOW To adjust CustomTV Film Turn OFF ProgressiveMY Memory LOAD1 LOAD2 LOAD3 LOAD4Image menu PhaseNormal Over ScanAt a video signal Auto AdjustSize ExecuteSpace Auto RGB Input menuVideo Format Auto Ntsc PAL SecamInformation Frame LockTurn on Turn OFF Volume Setup menuNormal Whisper Normal Hinvert Vinvert H&VINVERTScreen menu Original Turn OFF Start UPSync is OUT of Range MessageNo Input is Detected Search Option menuRGB S-VIDEO Video Auto OFFLamp Time Reset  CancelFAN Speed Auto Adjust Factory Reset Ghost ServiceEnable Disable High NormalLamp MaintenanceCase of replacement by yourself Air filter ViewSonic PJ400 Inside of the projector Other careRelated messages TroubleshootingInternal portion temperature is rising Regarding the indicator lamps Cooling fan is not operating It is time to clean the air filter, or there is no airThere is a possibility that the interior portion Has become heatedPhenomena that may easily be mistaken for machine defects Electrical power cord is not pluggedPower switch is not set to the on position Brightness is adjusted to an extremely Signal cables are not correctly connectedColor settings are not correctly adjusted 25, 28 Color Space setting is not suitableSpecifications Warranty and after-serviceSpecifications Unit mm Land/Region Web site = Telephone Mail Customer SupportLimited Warranty ViewSonic Projector
Top Page Image Contents