ViewSonic PJ400 manual Using the partial magnify feature, Freezing the screen

Page 25

Using the partial magnify feature

1. Press the ON button of MAGNIFY on the remote control. The “MAGNIFY” indication will appear on the screen (although the indication will disappear after several seconds

with no operation), and the projector will enter the MAGNIFY mode

2. Use the cursor buttons / to adjust the zoom level.

To move the zoom area, press the POSITION button in the MAGNIFY mode, the use the cursor buttons / / / to move the area. And to finalize the zoom area, press the POSITION button again.

To exit the MAGNIFY mode and restore the screen to normal, press the OFF button of MAGNIFY on the remote control.

The projector automatically exits the MAGNIFY mode when the input signal changes, or when an operation of changing the display condition (automatic adjustment, etc.) is executed.

Although in the MAGNIFY mode, the keystone distortion condition may vary, it will be restored when the projector exit the MAGNIFY mode.

Freezing the screen

1. Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen, and the projector will enter the FREEZE mode.

To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again.

The projector automatically exits the FREEZE mode when the input signal changes, or when one of the projector’s buttons or the remote control buttons of

STANDBY/ON, SEARCH, RGB, VIDEO, BLANK, AUTO, ASPECT, VOLUME, MUTE, KEYSTONE, POSITION and MENU is pressed.

If the projector continues projecting a still image for long time, the LCD panel might possibly be printed. Do not leave the projector in FREEZE mode for too long.

Temporarily blanking the screen

1. Press the BLANK button on the remote control.

The blank screen will be displayed instead of the screen of input signal. Please refer to the item BLANK of section SCREEN menu ( 35).

To remove the blank screen and return to the input signal screen, press the BLANK button again.

The projector automatically returns to the input signal screen when the input signal changes, or when one of the projector’s buttons or the remote control buttons are pressed.

ViewSonic PJ400

21

Image 25
Contents PJ400 LCD Projector Compliance Information Important Safety Instructions Copyright Information About this manual PJ400 Model No.VS10459Trademark acknowledgment Contents About contents of package Projector featuresProjector Part namesControls Remote controlMagnify Fastening the lens cover PreparationsPutting batteries Using the remote control About the filter cover for bottom-up use Setting up At 43 screen ArrangementAdjusting the projectors elevator About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting power supply Turning on the power Power on/offTurning off the power Selecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom magnifying power Searching an input signalAdjusting the focus Selecting an aspect ratioAt a video signal Using the automatic adjustment featureAdjusting the position Correcting the keystone distortionsFreezing the screen Using the partial magnify featureTemporarily blanking the screen Using the menu function Multifunctional settingTo display a menu To choose the target menuTo choose the target item To reset Setup MenuTo operate To return to the previous menuZoom AspectKeystone ModeWhisper ResetMirror Filter TimeUsing a test pattern To adjust #1 CUSTOM, #2 Custom or #3 CustomPicture menu High Middle Custom LOW To adjust CustomTV Film Turn OFF ProgressiveMY Memory LOAD1 LOAD2 LOAD3 LOAD4Image menu PhaseNormal Over ScanAt a video signal Auto AdjustSize ExecuteSpace Auto RGB Input menuVideo Format Auto Ntsc PAL SecamTurn on Turn OFF Frame LockInformation Volume Setup menuNormal Whisper Normal Hinvert Vinvert H&VINVERTScreen menu Original Turn OFF Start UPNo Input is Detected MessageSync is OUT of Range Search Option menuRGB S-VIDEO Video Auto OFFLamp Time Reset  CancelFAN Speed Auto Adjust Factory Reset Ghost ServiceEnable Disable High NormalLamp MaintenanceCase of replacement by yourself Air filter ViewSonic PJ400 Inside of the projector Other careRelated messages TroubleshootingInternal portion temperature is rising Regarding the indicator lamps Cooling fan is not operating It is time to clean the air filter, or there is no airThere is a possibility that the interior portion Has become heatedPower switch is not set to the on position Electrical power cord is not pluggedPhenomena that may easily be mistaken for machine defects Brightness is adjusted to an extremely Signal cables are not correctly connectedColor settings are not correctly adjusted 25, 28 Color Space setting is not suitableSpecifications Warranty and after-serviceSpecifications Unit mm Land/Region Web site = Telephone Mail Customer SupportLimited Warranty ViewSonic Projector