ViewSonic PJ400 manual Lamp Time, Reset  Cancel

Page 43

OPTION menu (continued)

Item

Description

LAMP TIME

The lamp time is the time counted after the last resetting. It is

 

shown in the OPTION menu as the use time of the lamp.

 

Performing this item resets the time.

 

Pressing the RESET button on the remote control or the button

 

► on the projector for about 3 seconds displays a dialog to

 

make sure. To perform reset, point at RESET using the button

 

▲.

 

RESET CANCEL

 

• Please reset the lamp time only when you have replaced the

 

lamp, for correct messages about the lamp.

 

• About the lamp replacement, please see the section “Lamp.”

 

( 41, 42)

FILTER TIME

The filter time is the time counted after the last resetting. It is

 

shown in the OPTION menu as the use time of the air filter.

 

Performing this item resets the time.

 

Pressing the RESET button on the remote control or the button

 

► on the projector for about 3 seconds displays a dialog to

 

make sure. To perform reset, point at RESET using the button

 

▲.

 

RESET CANCEL

 

• Please reset the filter time only when you have cleaned or

 

replaced the air filter, for correct messages about the air filter.

 

• About the caring the air filter, please see the section “Air

 

filter.” ( 43)

ViewSonic PJ400

39

Image 43
Contents PJ400 LCD Projector Compliance Information Important Safety Instructions Copyright Information About this manual PJ400 Model No.VS10459Trademark acknowledgment Contents About contents of package Projector featuresProjector Part namesControls Remote controlMagnify Fastening the lens cover PreparationsPutting batteries Using the remote control About the filter cover for bottom-up use Setting up At 43 screen ArrangementAdjusting the projectors elevator About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting power supply Turning on the power Power on/offTurning off the power Temporarily muting the sound Adjusting the volumeSelecting an input signal OperatingSelecting an aspect ratio Searching an input signalAdjusting the zoom magnifying power Adjusting the focusCorrecting the keystone distortions Using the automatic adjustment featureAt a video signal Adjusting the positionFreezing the screen Using the partial magnify featureTemporarily blanking the screen To choose the target menu Multifunctional settingUsing the menu function To display a menuTo choose the target item To return to the previous menu Setup MenuTo reset To operateMode AspectZoom KeystoneFilter Time ResetWhisper MirrorUsing a test pattern To adjust #1 CUSTOM, #2 Custom or #3 CustomPicture menu High Middle Custom LOW To adjust CustomLOAD1 LOAD2 LOAD3 LOAD4 ProgressiveTV Film Turn OFF MY MemoryOver Scan PhaseImage menu NormalExecute Auto AdjustAt a video signal SizeFormat Auto Ntsc PAL Secam Input menuSpace Auto RGB VideoTurn on Turn OFF Frame LockInformation Normal Hinvert Vinvert H&VINVERT Setup menuVolume Normal WhisperScreen menu Original Turn OFF Start UPNo Input is Detected MessageSync is OUT of Range Auto OFF Option menuSearch RGB S-VIDEO VideoLamp Time Reset  CancelHigh Normal ServiceFAN Speed Auto Adjust Factory Reset Ghost Enable DisableLamp MaintenanceCase of replacement by yourself Air filter ViewSonic PJ400 Inside of the projector Other careRelated messages TroubleshootingInternal portion temperature is rising Regarding the indicator lamps Has become heated It is time to clean the air filter, or there is no airCooling fan is not operating There is a possibility that the interior portionPower switch is not set to the on position Electrical power cord is not pluggedPhenomena that may easily be mistaken for machine defects Color Space setting is not suitable Signal cables are not correctly connectedBrightness is adjusted to an extremely Color settings are not correctly adjusted 25, 28Specifications Warranty and after-serviceSpecifications Unit mm Land/Region Web site = Telephone Mail Customer SupportLimited Warranty ViewSonic Projector