ViewSonic PJ400 manual Case of replacement by yourself

Page 46

When the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible.

1.Turn the projector off, and unplug the power cord. Allow the lamp to cool for at least 45 minutes.

2.To prepare a new lamp, contact your dealer and tell the lamp type number = RLC-004. If the projector is mounted on the ceiling, or if the lamp has broken, also ask the dealer to replace the lamp.

In the case of replacement by yourself,

3.After making sure that the projector has cooled adequately, slowly turn over the projector, so that the bottom is facing up.

4.Please loosen the screw (marked by arrow). Then, unhook the claws of the lamp cover and remove the lamp cover.

5.Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the

handles.

6.Insert the new lamp, and retighten firmly two screws that are loosened in the previous process to lock it in place.

7.Interlocking the 2 tabs of the lamp cover to the projector, position the lamp cover on the projector, and push

the center point of two claws to fix the lamp cover. Then retighten firmly the screw of the lamp cover.

8.Slowly turn the projector so that the top is facing up.

9. Turn the projector on, and reset the lamp time. ( 39)

(1)While the projector running, press the MENU button to open the menu.

(2)Choose the “LAMP TIME” on the "OPTION" menu (of Advanced Menu) using ▲/▼ button, then press and hold the RESET button or the ► button for 3 seconds.

(3)Choose the “RESET” using the ▲ button.

NOTE.

•When the lamp has been replaced after the message of "THE POWER WILL TURN OFF AFTER 0hr." is displayed, complete the following operation within 10 minutes of switching power on.

•Incorrectly resetting of the lamp timer (resetting without replacement, or neglect of resetting after replacement) will result in incorrect message functions.

ViewSonic PJ400

42

Image 46

Contents PJ400 LCD Projector Compliance Information Important Safety Instructions Copyright Information About this manual PJ400 Model No.VS10459Trademark acknowledgment Contents Projector features About contents of packagePart names ProjectorControls Remote controlMagnify Preparations Fastening the lens coverPutting batteries Using the remote control About the filter cover for bottom-up use Setting up Arrangement At 43 screenAdjusting the projectors elevator Connecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting power supply Power on/off Turning on the powerTurning off the power Operating Adjusting the volumeSelecting an input signal Temporarily muting the soundAdjusting the focus Searching an input signalAdjusting the zoom magnifying power Selecting an aspect ratioAdjusting the position Using the automatic adjustment featureAt a video signal Correcting the keystone distortionsFreezing the screen Using the partial magnify featureTemporarily blanking the screen To display a menu Multifunctional settingUsing the menu function To choose the target menuTo choose the target item To operate Setup MenuTo reset To return to the previous menuKeystone AspectZoom ModeMirror ResetWhisper Filter TimeUsing a test pattern To adjust #1 CUSTOM, #2 Custom or #3 CustomPicture menu To adjust Custom High Middle Custom LOWMY Memory ProgressiveTV Film Turn OFF LOAD1 LOAD2 LOAD3 LOAD4Normal PhaseImage menu Over ScanSize Auto AdjustAt a video signal ExecuteVideo Input menuSpace Auto RGB Format Auto Ntsc PAL SecamTurn on Turn OFF Frame LockInformation Normal Whisper Setup menuVolume Normal Hinvert Vinvert H&VINVERTScreen menu Start UP Original Turn OFFNo Input is Detected MessageSync is OUT of Range RGB S-VIDEO Video Option menuSearch Auto OFF Reset  Cancel Lamp TimeEnable Disable ServiceFAN Speed Auto Adjust Factory Reset Ghost High NormalMaintenance LampCase of replacement by yourself Air filter ViewSonic PJ400 Other care Inside of the projectorTroubleshooting Related messagesInternal portion temperature is rising Regarding the indicator lamps There is a possibility that the interior portion It is time to clean the air filter, or there is no airCooling fan is not operating Has become heatedPower switch is not set to the on position Electrical power cord is not pluggedPhenomena that may easily be mistaken for machine defects Color settings are not correctly adjusted 25, 28 Signal cables are not correctly connectedBrightness is adjusted to an extremely Color Space setting is not suitableWarranty and after-service SpecificationsSpecifications Unit mm Customer Support Land/Region Web site = Telephone MailLimited Warranty ViewSonic Projector