Eiki LC-X6, LC-SX6 owner manual To The Owner, Risk of Electric Shock Do not Open

Page 4

To The Owner

Before operating this projector, read this manual thoroughly and operate the projector properly.

This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.

Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.

If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Troubleshooting” section in the end of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.

Safety Precaution

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. Eye damage could result. Be especially careful that children do not stare directly into the beam.

Install the projector in a proper position. If not, it may result in a fire hazard.

Provide appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. Minimum clearance must be maintained. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build- up can reduce the service life of your projector, and can

also be dangerous.

SIDE and TOP

REAR

3.3'(1m)

3.3'(1m)

3.3'(1m)

3.3'(1m)

Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.

If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

Ne peut être utilisé dans une salle d’ordinateurs telle que définie dans la norme ANSI/NFPA 75 Standard for Protection of Electronic Computer/Data Processing Equipment

Trademarks

Each name of corporations or products in this book is either a registered trademark or a trademark of its respective corporation.

Remark

Any graphic and figure in this manual are subject to change without notice.

4

Image 4
Contents LC-SX6 Features and Design Compatibility My LogoTable of Contents To The Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandSetup In Proper Directions Positioning PrecautionsAir Circulation Bottom Front Downward Upward UsualMoving the Projector USE Caution in Carrying or Transporting the ProjectorCompliance Federal Communication Commission NoticePreparation Parts NameFront BackIndicators Top Control About Control PadTerminals Input 2 terminalsC Jack USBUSB Series B Serial Port OUTRemote Control Timer button 4REMOTE RESET/ON/ALL-OFF switchFreeze button VOL. buttonRemote Control Channel and ID Setup Remote Control TransmitterWired Remote Control Transmitter Remote Control Channel & Frequency Remote Control Battery InstallationRemote Control ID Installation InstallationLens Installation Positioning the ProjectorLens Shift Adjustment Level Adjustable FeetConnecting AC Power Cord For Continental EuropeFor the U.S.A. and Canada 200 240 V ACInterface Board Slots Connection TerminalsOption Control No Connecting to Computer Digital and Analog RGB Cables used for connectionConnecting to Digital PC/AV Equipment Warp & Blending Connecting to Video Equipment Digital and Video Connecting to Video Equipment Component and RGB Scart Wireless Remote Control Operation Basic OperationOperating the Projector Mouse Operation Projector Top Control OperationBasic Operation and Reference Buttons Top Control Remote ControlPad What is PIN code? Turning On the ProjectorEnter a PJ PIN code Selected Input and SourceTurning Off the Projector Zoom and Focus Adjustment Remote ControlShutter Function Top ControlInput Selection Auto PC AdjustmentInformation Keystone Adjustment Timer FunctionScreen Selection Picture Freeze FunctionVolume Control Zoom +/- FunctionTop Control/Remote Control Operation How to Operate the On-Screen MenuMouse Operation Menu icon Guide Control bar for Mouse OperationMouse cursor PointerMenu Icons and Their Features Menu icons What You Can Do with Each MenuInput InputRGB Scart Video Video Pb/Cb, Pr/CrVideo System SystemPC System Selection AutoVideo or S-Video Signal Selection Component Signal SelectionAV System Menu Video or S-Video AV System Menu ComponentComputer Adjustment PC AdjustmentAuto PC Adjust Auto PC adjManual PC Adjust Sync phase ResetPosition ModeImage Adjustment ImageFor PC Input For AV InputImage Adjust Auto picture control Color tempRed GreenGamma Noise reductionProgressive FilmScreen Setting Screen SettingScreen Zoom KeystoneCeiling RearSound SoundSound Menu TrebleSetting SettingLanguage MenuLogo Enter a Logo PIN codeBackground LampPower management Power managementDisplay Input searchLens memory Analog outShutter Shutter Management SecurityKey lock USB lockTo Change the PJ PIN Code setting To Change PJ PIN CodeFactory default Exits the Setting menuSpecial SpecialFan control FilterRS-232C Test patternUSB memory Exits Warning log menu InformationAll indicators except the Lamp indicator are blinking3 Maintenance and CleaningThen check the matters below Air Filter Replacement Maintenance & CleaningReset the Lamp time Lamp ReplacementLamp Lamp Handling Precautions Cleaning the Projector Cabinet Cleaning the Projection LensAttaching the Cord Cover Strap Indicators and Projector Condition Main IndicatorsAir filter is clogged with dust or has been used overtime Shutter IndicatorSlow Lamp Replace Indicators Troubleshooting AppendixWireless Remote Control Lens position moves when InputIs switched No soundCompatible Computer Specifications FreqVGA Technical Specifications Accessories Optional PartsScreen Setting Sound Menu TreeImage Image ADJ Special Lamp Dimensions Terminal Configurations USB Connector Series BPIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Index NumericsAppendix Key to better communications Canada