Intel D865PCD specifications Runtime Code Uncompressed in F000 Shadow RAM

Page 105

Error Messages and Beep Codes

Table 66. Runtime Code Uncompressed in F000 Shadow RAM (continued)

Code

40

42

43

44

45

46

47

48

49

4B

4C

4D

4E

4F

50

51

52

53

54

57

58

59

60

62

65

66

7F

80

81

82

83

Description of POST Operation

To prepare the descriptor tables.

To enter in virtual mode for memory test.

To enable interrupts for diagnostics mode.

To initialize data to check memory wrap around at 0:0.

Data initialized. Going to check for memory wrap around at 0:0 and finding the total system memory size.

Memory wrap around test done. Memory size calculation over. About to go for writing patterns to test memory.

Pattern to be tested written in extended memory. Going to write patterns in base 640k memory.

Patterns written in base memory. Going to find out amount of memory below 1M memory.

Amount of memory below 1M found and verified. Going to find out amount of memory above 1M memory.

Amount of memory above 1M found and verified. Check for soft reset and going to clear memory below 1M for soft reset. (If power on, go to check point # 4Eh).

Memory below 1M cleared. (SOFT RESET) Going to clear memory above 1M.

Memory above 1M cleared. (SOFT RESET) Going to save the memory size. (Go to check point # 52h).

Memory test started. (NOT SOFT RESET) About to display the first 64k memory size.

Memory size display started. This will be updated during memory test. Going for sequential and random memory test.

Memory testing/initialization below 1M complete. Going to adjust displayed memory size for relocation/shadow.

Memory size display adjusted due to relocation/ shadow. Memory test above 1M to follow.

Memory testing/initialization above 1M complete. Going to save memory size information.

Memory size information is saved. CPU registers are saved. Going to enter in real mode.

Shutdown successful, CPU in real mode. Going to disable gate A20 line and disable parity/NMI.

A20 address line, parity/NMI disable successful. Going to adjust memory size depending on relocation/shadow.

Memory size adjusted for relocation/shadow. Going to clear Hit <DEL> message.

Hit <DEL> message cleared. <WAIT...> message displayed. About to start DMA and interrupt controller test.

DMA page register test passed. To do DMA#1 base register test.

DMA#1 base register test passed. To do DMA#2 base register test.

DMA#2 base register test passed. To program DMA unit 1 and 2.

DMA unit 1 and 2 programming over. To initialize 8259 interrupt controller.

Extended NMI sources enabling is in progress.

Keyboard test started. Clearing output buffer, checking for stuck key, to issue keyboard reset command.

Keyboard reset error/stuck key found. To issue keyboard controller interface test command.

Keyboard controller interface test over. To write command byte and init circular buffer.

Command byte written, global data init done. To check for lock-key.

continued

105

Image 105
Contents D865PCD Revision Revision HistoryDate Preface Other Common Notation Intel Desktop Board D865PCD Technical Product SpecificationContents Overview of Bios Features Contents Bios Setup ProgramFigures Desktop Board D865PCD Environmental Specifications Intel Desktop Board D865PCD Technical Product Specification Product Description Summarizes the major features of the Desktop Board D865PCD Feature SummaryFeature Summary OverviewProduct Description Board LayoutBlock Diagram Block DiagramOnline Support To find information about…Product Description Visit this World Wide Web site Specifications Design SpecificationsReference Specification Name Title Version, Revision Date, and OwnershipVersion, Revision Date and Ownership Sdram SpecificationBios # INTEGRATOR’S Notes ProcessorTo use this type of DIMM… System MemoryProcessors system bus frequency must be… For information about Refer toSupported Memory Configurations Lists the supported Dimm configurationsConfiguration Memory ConfigurationsCharacteristics Throughput LevelSingle Channel Configuration with Dynamic Mode Single Dimm Intel 865P Chipset Universal 0.8 V / 1.5 V AGP 3.0 Connector2 USB IDE Support Real-Time Clock, Cmos SRAM, and BatterySerial Port I/O ControllerParallel Port Diskette Drive ControllerFront Panel Audio Connector Audio ConnectorsAudio Subsystem Keyboard and Mouse InterfaceLAN Subsystem Atapi CD-ROM Audio ConnectorAudio Subsystem Software Intel 82562EZ Physical Layer Interface Device2 RJ-45 LAN Connector with Integrated LEDs Power ManagementLAN Connector LED States Chassis Intrusion and Detection Power Management Event signal PME# wake-up support System States and Power StatesEffects of Pressing the Power Switch AcpiPower States and Targeted System Power Wake-up Devices and EventsWake-up Devices and Events Hardware Support Power ConnectorInstantly Available PC Technology LAN Wake CapabilitiesResume on Ring 11.2.7 PME# Signal Wake-up SupportWake from USB Wake from PS/2 DevicesIntel Desktop Board D865PCD Technical Product Specification Memory Map IntroductionLists the system memory map System Memory MapFixed I/O Map DMA ChannelsDMA Channels O MapPCI Configuration Space Map PCI Configuration Space MapTechnical Reference Interrupts InterruptsPCI Interrupt Routing Map PCI Interrupt Routing Map ICH5 Pirq Signal Name PCI Interrupt Source LAN ConnectorsDescription Color Back Panel ConnectorsExpansion Slots Internal I/O ConnectorsDescription For more information see Audio ConnectorsFront Panel Audio Connector Atapi CD-ROM ConnectorSignal Name Pin Signal NamePower and Hardware Control Connectors Power and Hardware Control ConnectorsATX12V Power Connector Rear Chassis Fan ConnectorProcessor Fan Connector Main Power ConnectorChassis Intrusion Connector Front Chassis Fan ConnectorD865PCD Add-in Board and Peripheral Interface Connectors Add-in Board and Peripheral Interface ConnectorsDescription Color For more information see External I/O ConnectorsFront Panel Connector Front Panel ConnectorStates for a Two-Color Power LED States for a One-Color Power LEDConnection Diagram for Front Panel USB Connector Is a connection diagram for the front panel USB connectorJumper Blocks Front Panel Audio Connector/Jumper BlockFront Panel Audio Connector/Jumper Block Bios Setup Configuration Jumper BlockBios Setup Configuration Jumper Settings Jumper SettingForm Factor Mechanical Considerations10.2 I/O Shield O Shield DimensionsLists the current capability of the fan connectors Fan Connector Current CapabilityElectrical Considerations DC LoadingThermal Considerations Power Supply ConsiderationsShows the locations of the localized high temperature zones Reliability Maximum Case TemperatureThermal Considerations for Components ComponentParameter Temperature Desktop Board D865PCD Environmental SpecificationsEnvironmental ShockSafety Regulations Safety RegulationsRegulatory Compliance EMC RegulationsEuropean Union Declaration of Conformity Statement FCC Compliance Statement USACanadian Compliance Statement Product Certification Markings Board Level Product Ecology StatementsDisposal Considerations Recycling ConsiderationsIntel Desktop Board D865PCD Technical Product Specification Bios Flash Memory Organization Overview of Bios FeaturesResource Configuration PCI AutoconfigurationPCI IDE Support System Management Bios Smbios Overview of Bios FeaturesLegacy USB Support Language Support Bios UpdatesCustom Splash Screen Recovering Bios DataCD-ROM Boot Boot OptionsNetwork Boot Booting Without Attached DevicesFast Booting Systems with Intel Rapid Bios Boot Peripheral Selection and ConfigurationIntel Rapid Bios Boot Supervisor and User Password Functions Bios Security FeaturesBios Setup Program Menu Bar Lists the Bios Setup program menu featuresBios Setup Program Function Keys Maintenance MenuMaintenance Menu Lists the function keys available for menu screensMain Menu Main MenuAdvanced Menu Advanced MenuPCI Configuration Submenu PCI Configuration SubmenuOptions Auto default Description Boot Configuration Submenu Boot Configuration SubmenuOptions No default On default DescriptionPeripheral Configuration Submenu Peripheral Configuration SubmenuAuto default 3F8 default IRQ 4 default DescriptionDefault Bi-directional defaultIRQ 7 default Description Default Enabled defaultMenu represented in is used to configure IDE device options Drive Configuration SubmenuDrive Configuration Submenu Enabled default Disabled defaultPata Submenus Pata Submenus Floppy Configuration Submenu Floppy Configuration Submenu44 MB ½ default Event Log Configuration Submenu Event Log Configuration SubmenuEnabled default Ok default Video Configuration Submenu Video Configuration SubmenuMB default AGP defaultSubmenu represented in is for configuring the USB features USB Configuration SubmenuUSB Configuration Submenu Options Enabled defaultSubmenu represented in is for configuring chipset options Chipset Configuration SubmenuChipset Configuration Submenu Default defaultDefault Description Options Auto defaultFull default If no password entered previously FeatureSecurity Menu Security MenuPower Menu Power MenuAcpi Submenu Acpi SubmenuBoot Menu Boot MenuBoot Device Priority Submenu Submenu represented in is for setting boot devices priorityBoot Device Priority Submenu Removable Devices Submenu Hard Disk Drives SubmenuHard Disk Drives Submenu Removable Devices SubmenuAtapi CD-ROM Drives Submenu Exit MenuAtapi CD-ROM Drives Submenu Exit Menu100 Bios Error Messages Bios Error MessagesError Message ExplanationBios Error Messages Error Messages and Beep Codes Boot Block Recovery Code CheckpointsPort 80h Post Codes Uncompressed Init Code CheckpointsRuntime Code Uncompressed in F000 Shadow RAM Runtime Code Uncompressed in F000 Shadow RAM Runtime Code Uncompressed in F000 Shadow RAM Bus Initialization Checkpoints Bus Initialization CheckpointsUpper Nibble High Byte Functions Checkpoint DescriptionBios Beep Codes SpeakerLower Nibble High Byte Functions Beep Description Beep Codes110