Intel GA-8I915PM-FS Integrated Peripherals, Pata IDE Set to, Sata Port 0/2 Set to, USB Controller

Page 30

English

2-3

Integrated Peripherals

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

 

Integrated Peripherals

 

 

 

On-Chip Primary PCI IDE

[Enabled]

 

Item Help

 

On-Chip SATA Mode

 

[Auto]

 

Menu Level`

x

PATA IDE Set to

 

Ch.0 Master/Slave

 

 

 

SATA Port 0/2 Set to

 

Ch.2 Master/Slave

 

 

 

SATA Port 1/3 Set to

 

Ch.3 Master/Slave

 

 

 

USB Controller

 

 

[Enabled]

 

 

 

 

USB 2.0 Controller

 

[Enabled]

 

 

 

 

USB Keyboard Support

 

[Enabled]

 

 

 

 

USB Mouse Support

 

[Enabled]

 

 

 

 

Azalia Codec

 

 

[Auto]

 

 

 

 

]

 

 

 

 

 

 

 

Onboard H/W 1394

 

[Enabled]

 

 

 

 

Onboard H/W LAN

 

[Enabled]

 

 

 

 

Onboard LAN Boot ROM

 

[Disabled]

 

 

 

 

Onboard Serial Port 1

 

[3F8/IRQ4]

 

 

 

Onboard Parallel Port

 

[378/IRQ7]

 

 

 

Parallel Port Mode

 

[ECP+EPP]

 

 

 

ECP Mode Use DMA

 

[3]

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

 

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

On-Chip Primary PCI IDE

 

 

 

 

 

Enabled

 

Enable onboard 1st channel IDE port. (Default value)

 

 

Disabled

 

Disable onboard 1st channel IDE port.

 

 

 

On-Chip SATA Mode

 

 

 

 

 

Disabled

 

Disable this function.

 

 

 

 

Auto

 

BIOS will auto detect. (Default value)

 

 

 

Combined

 

Set On-Chip SATA mode to Combined, you can use up to 4 HDDs on the

 

 

 

motherboard; 2 for SATA and the other for PATA.

 

 

Enhanced

 

Set On-Chip SATA mode to Enhanced, the motherboard allows up to 6 HDDs

 

 

 

to use; 4 SATA HDDs plus PATA HDDs.

 

 

 

Non-Combined

Set On-Chip SATA mode to Non-Combined, SATA will be simulated to PATA

 

 

 

mode. Support a maximum of 4 SATA devices. PATA devices will be ignored.

PATA IDE Set to

Ch.0 Master/Slave Set PATA IDE to Ch. 0 Master/Slave. (Default value)

Ch.1 Master/Slave Set PATA IDE to Ch. 1 Master/Slave.

SATA Port 0/2 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 1 Master/Slave, this function will auto set to Ch. 0 Master/Slave.

SATA Port 1/3 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 0 Master/Slave, this function will auto set to Ch. 1 Master/Slave.

USB Controller

Enabled

Enable USB controller. (Default value)

Disabled

Disable USB controller.

GA-8I915PM-FS Motherboard

- 30 -

Image 30
Contents GA-8I915PM-FS Table of Contents GA-8I915PM-FS Motherboard Layout 8I915PM-GABlock Diagram Hardware Installation Considerations Prior to InstallationFeature Summary CPUALC880 Codec Installation of the CPU and Heatsink HT functionality requirement contentInstallation of the Heatsink Installation of Memory Dual Channel DDR Memory Configuration Install expansion cards I/O Back Panel Introduction Connectors Introduction Side Speaker OutATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE IDE Connector Azaliafp Front Audio Connector Fpanel Front Panel JumperCdin CD in Connector USB1 / FUSB2 Front USB Connector12 F11394 / F21394 Front Ieee 1394 Connector 13 IRSafemode Clrcmos Clear CmosBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver D „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupTime Standard Cmos FeaturesDate IDE Channel 0 Master/SlaveMemory Drive aHalt on Base MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckNo-Execute Memory ProtectNote CPU Hyper-ThreadingLimit Cpuid Max. to CPU Enhanced Halt C1E NoteSata Port 0/2 Set to Integrated PeripheralsPata IDE Set to Sata Port 1/3 Set toECP Mode Use DMA Onboard LAN Boot ROMParallel Port Mode USB 2.0 ControllerResume by Alarm Power Management SetupPower On by Ring Power On by MousePower On by Keyboard KB Power on PasswordAC Back Function PnP/PCI Configurations INTPC Health Status Frequency/Voltage Control Memory Frequency ForMemory Frequency Mhz Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish