Intel GA-8VM800PMD-775 user manual Pwrled, Faudio Front Audio Panel Connector

Page 22

English

9)PWR_LED

PWR_LED is connected with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode.

1

Pin No.

Definition

 

1

MPD+

 

2

MPD-

 

3

MPD-

 

 

 

10)F_AUDIO (Front Audio Panel Connector)

Please make sure the pin assignment on the cable is the same as the pin assigment on the MB header. To find out if the chassis you are buying support front audio panel connector, please contact your dealer. If you want to use "Front Audio" connector, you must remove the jumpers from pins 5-6, 9-10.

 

 

Pin No.

Definition

10

9

1

MIC

2

GND

 

 

2

1

3

MIC_BIAS

4

POWER

 

 

 

 

5

FrontAudio(R)

 

 

6

Rear Audio (R)/ Return R

 

 

7

NC

 

 

8

No Pin

 

 

9

FrontAudio (L)

 

 

10

Rear Audio (L)/ Return L

GA-8VM800PMD-775 Motherboard

- 22 -

Image 22
Contents GA-8VM800PMD-775 Motherboard GA-8VM800PMD-775 Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8VM800PMD-775 Motherboard Layout VIA775-8VM800PMDBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPU4Mbit flash ROM Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction EnglishATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorFpanel Front Panel Connector Faudio Front Audio Panel Connector PwrledCdin CD in Connector, black Auxin AUX In Connector, whiteSpdifio Spdif In/ Out connector, red Surcen Surround Center Connector, black15 F1USB / F2USB Front USB Connectors Comb Comb ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D1 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupIDE Channel 0/1 Master, Slave Standard Cmos FeaturesTime IDE Channel 2/3 MasterHalt on Floppy 3 Mode Support for Japan AreaDrive a MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckNo-Execute Memory Protect Note CPU Hyper-ThreadingLimit Cpuid Max. to CPU Enhanced Halt C1E NoteIntegrated Peripherals IDEEPP Mode Select OnBoard LAN Boot ROMParallel Port Mode USB Mouse SupportPower Management Setup Acpi OSPME Event Wake Up Mouse Power OnResume by Alarm Modem Ring ResumePnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency / Voltage Control AGP OverVoltage Control Dram ClockDimm OverVoltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewWhat is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish To configure Sata hard drives, follow the steps below Configuring Sata Hard DrivesInstall Sata hard drives in your system IDE Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation RAID array, select VIA ATA/ATAPI Host ControllerWindows XP Enter= Continue R=Repair F3=Exit Channel Audio Setup 5 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai