Intel GA-8VM800PMD-775 user manual RAID array, select VIA ATA/ATAPI Host ControllerWindows XP

Page 75

Step 3:

If Setup correctly recognizes the driver in the floppy disk, a controller menu similar to Figure 18 below will appear. If you want to install Windows XP, use the ARROW keys to select VIA Serial ATA RAID Controller(Windows XP)(Note) and press ENTER. Then it will begin to load the SATA driver from the floppy disk.

Windows Setup

You have chosen to configure a SCSI Adapter for use with Windows, using a device support disk provided by an adapter manufacturer.

Select the SCSI Adapter you want from the following list, or press ESC to return to the previous screen.

VIA Serial ATA RAID Controller(Windows XP)

VIA Serial ATA RAID Controller(Windows 2000)

VIA Serial ATA RAID Controller(Windows NT4)

VIA ATA/ATAPI Host Controller(Windows XP)

ENTER=Select F3=Exit

Figure 18

If a message appears saying one or some file(s) cannot be found, please check the floppy disk or copy the correct SATA driver again from the motherboard driver CD.

Step 4:

When the screen as shown below appears, press ENTER to continue the SATA driver installation from the floppy disk. The driver installation will be finished in about one minute.

Windows Setup

Setup will load support for the following mass storage device(s):

VIA Serial ATA RAID Controller(Windows XP)

*To specify additional SCSI adapters, CD-ROM drives, or special disk controllers for use with Windows, including those for which you have a device support disk from a mass storage device manufacturer, press S.

*If you do not have any device support disks from a mass storage device manufacturer, or do not want to specify additional mass storage devices for use with Windows, press ENTER.

S=Specify Additional Device Enter=Continue F3=Exit

Figure 19

(Note) If you want to create a RAID array, select the item depending on the operating system that you want to install. (Windows XP, Windows 2000 or Windows NT4). If you do not want create a

RAID array, select VIA ATA/ATAPI Host Controller(Windows XP).

 

- 75 -

Appendix

English

Image 75
Contents GA-8VM800PMD-775 Motherboard GA-8VM800PMD-775 Product Manual Classification CopyrightTable of Contents Drivers Installation VIA775-8VM800PMD GA-8VM800PMD-775 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature Summary4Mbit flash ROM Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction English Connectors IntroductionATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorAuxin AUX In Connector, white Cdin CD in Connector, blackSurcen Surround Center Connector, black Spdifio Spdif In/ Out connector, redComb Comb Connector 15 F1USB / F2USB Front USB ConnectorsClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. D1 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 2/3 Master Standard Cmos FeaturesTime IDE Channel 0/1 Master, SlaveMemory Floppy 3 Mode Support for Japan AreaDrive a Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceCPU Enhanced Halt C1E Note CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory Protect NoteIDE Integrated PeripheralsUSB Mouse Support OnBoard LAN Boot ROMParallel Port Mode EPP Mode SelectAcpi OS Power Management SetupModem Ring Resume Mouse Power OnResume by Alarm PME Event Wake UpPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Frequency / Voltage Control Dram Clock AGP OverVoltage ControlDimm OverVoltage Control Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Press F9 during powering on the computer. Text Mode F9 For Xpress RecoveryExit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Configuring Sata Hard Drives To configure Sata hard drives, follow the steps belowInstall Sata hard drives in your system IDE Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation RAID array, select VIA ATA/ATAPI Host ControllerWindows XP Enter= Continue R=Repair F3=Exit 5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device AMI Bios Beep Codes TroubleshootingEnglish English English Taiwan Headquarters Contact UsChina Shanghai