Intel GA-8VM800PMD-775 user manual Serial Number View

Page 72

English

D. Serial Number View:

Highlight Serial Number View and press ENTER. Use the ARROW keys to select a drive, and the selected drive's serial number can be viewed in the last line. The serial number is assigned by the disk drive manufacturer (Figure 12).

VIA Tech. VT8237 SATA RAID BIOS Ver 2.31

Create Array

 

View the serial number of

Delete Array

 

hard disk, it is useful for

Create/Delete Spare

identify same model disks

Select Boot Array

F1

:

View Array/disk Status

Serial Number View

 

 

,

: Move to next item

 

 

Enter

:

Confirm the selection

 

 

ESC

:

Exit

Channel

Drive Name

Array Name

Mode

Size(GB)

Status

Serial_Ch0 Master

ST3120026AS

ARRAY 0

SATA

111.79

Stripe0

Serial_Ch1 Master

ST3120026AS

ARRAY 0

SATA

111.79

Stripe1

Serial Number:

3JT354CP

 

 

 

 

Figure 12

E. View Array Status:

Press F1 to show the array status on the lower screen. If there are no disk arrays then nothing will be displayed on the screen (Figure 13).

VIA Tech. VT8237 SATA RAID BIOS Ver 2.31

Create Array

Delete Array

Create/Delete Spare

Select Boot Array

Serial Number View

Create a RAID array with the hard disks attached to VIA RAID controller

F1 : View Array/disk Status

,: Move to next item Enter : Confirm the selection ESC : Exit

Array Name

Array Mode

Block Size(GB)

Size(GB)

ARRAY 0

Stripe

64K

223.58

Figure 13

GA-8VM800PMD-775 Motherboard

- 72 -

Image 72
Contents GA-8VM800PMD-775 Motherboard GA-8VM800PMD-775 Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8VM800PMD-775 Motherboard Layout VIA775-8VM800PMDBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPU4Mbit flash ROM Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction EnglishATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorFpanel Front Panel Connector Faudio Front Audio Panel Connector PwrledCdin CD in Connector, black Auxin AUX In Connector, whiteSpdifio Spdif In/ Out connector, red Surcen Surround Center Connector, black15 F1USB / F2USB Front USB Connectors Comb Comb ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D1 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeIDE Channel 0/1 Master, Slave IDE Channel 2/3 MasterFloppy 3 Mode Support for Japan Area Drive aHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals IDEOnBoard LAN Boot ROM Parallel Port ModeEPP Mode Select USB Mouse SupportPower Management Setup Acpi OSMouse Power On Resume by AlarmPME Event Wake Up Modem Ring ResumePnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency / Voltage Control Dram Clock AGP OverVoltage ControlDimm OverVoltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Configuring Sata Hard Drives To configure Sata hard drives, follow the steps belowInstall Sata hard drives in your system IDE Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation RAID array, select VIA ATA/ATAPI Host ControllerWindows XP Enter= Continue R=Repair F3=Exit Channel Audio Setup 5 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai