Intel GA-8VM800PMD-775 user manual Installing Sata controller driver during OS installation

Page 74

English

(5) Installing SATA controller driver during OS installation

Now that you have prepared the SATA driver disk and configured BIOS settings, you are ready to install Windows 2000/XP onto your SATA hard drive with the SATA driver. The following is an example of Windows XP installation.

Step 1: Restart your system to boot from the Windows 2000/XP Setup disk and press F6 as soon as you see the "Press F6 if you need to install a 3rd party SCSI or RAID driver" message (Figure 16). After pressing F6, there will be a few moments of some files being loaded before you see the next screen.

Windows Setup

Press F6 if you need to install a 3rd party SCSI or RAID driver.

Figure 16

Step 2:

When a screen similar to that below appears, insert the floppy disk containing the SATA driver and press S (Figure 17).

Windows Setup

Setup could not determine the type of one or more mass storage devices installed in your system, or you have chosen to manually specify an adapter. Currently, Setup will load support for the following mass storage devices(s)

<none>

*To specify additional SCSI adapters, CD-ROM drives, or special disk controllers for use with Windows, including those for which you have a device support disk from a mass storage device manufacturer, press S.

*If you do not have any device support disks from a mass storage device manufacturer, or do not want to specify additional mass storage devices for use with Windows, press ENTER.

S=Specify Additional Device ENTER=Continue F3=Exit

Figure 17

GA-8VM800PMD-775 Motherboard

- 74 -

Image 74
Contents GA-8VM800PMD-775 Motherboard GA-8VM800PMD-775 Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8VM800PMD-775 Motherboard Layout VIA775-8VM800PMDBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPU4Mbit flash ROM Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction EnglishATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorFpanel Front Panel Connector Faudio Front Audio Panel Connector PwrledCdin CD in Connector, black Auxin AUX In Connector, whiteSpdifio Spdif In/ Out connector, red Surcen Surround Center Connector, black15 F1USB / F2USB Front USB Connectors Comb Comb ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D1 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupIDE Channel 0/1 Master, Slave Standard Cmos FeaturesTime IDE Channel 2/3 MasterHalt on Floppy 3 Mode Support for Japan AreaDrive a MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckNo-Execute Memory Protect Note CPU Hyper-ThreadingLimit Cpuid Max. to CPU Enhanced Halt C1E NoteIntegrated Peripherals IDEEPP Mode Select OnBoard LAN Boot ROMParallel Port Mode USB Mouse SupportPower Management Setup Acpi OSPME Event Wake Up Mouse Power OnResume by Alarm Modem Ring ResumePnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency / Voltage Control Dimm OverVoltage Control Dram ClockAGP OverVoltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewHow to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Install Sata hard drives in your system Configuring Sata Hard DrivesTo configure Sata hard drives, follow the steps below IDE Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation RAID array, select VIA ATA/ATAPI Host ControllerWindows XP Enter= Continue R=Repair F3=Exit Channel Audio Setup 5 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai