Intel GA-8VM800PMD-775 user manual Integrated Peripherals, Ide

Page 36

English

2-3	Integrated Peripherals

			CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
				Integrated Peripherals
	OnChip IDE Channel 0			[Enabled]			Item Help
	OnChip IDE Channel 1			[Enabled]		Menu Level`
	OnChip Serial ATA			[Enabled]
	SATA Mode			[IDE]
	AC97 Audio			[Auto]
	USB 1.1 Controller			[Enabled]
	USB 2.0 Controller			[Enabled]
	USB Keyboard Support			[Disabled]
	USB Mouse Support			[Disabled]
	Onboard H/W LAN			[Enabled]
	OnBoard LAN Boot ROM			[Disabled]
	Legacy USB storage detect			[Enabled]
	Onboard Serial Port 1			[3F8/IRQ4]
	Onboard Serial Port 2			[2F8/IRQ3]
	Onboard Parallel Port			[378/IRQ7]
	Parallel Port Mode			[SPP]
x	EPP Mode Select			EPP1.7
KLJI: Move		Enter: Select		+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values			F6: Fail-Safe Defaults	F7: Optimized Defaults

	OnChip IDE Channel0
	Enabled		Enable onboard 1st channel IDE port. (Default value)
	Disabled		Disable onboard 1st channel IDE port.
	OnChip IDE Channel1
	Enabled		Enable onboard 2nd channel IDE port. (Default value)
	Disabled		Disable onboard 2nd channel IDE port.
	OnChip Serial ATA
	Enabled		Enable VT8237R Plus Serial ATA supported. (Default value)
	Disabled		Disable VT8237R Plus Serial ATA supported.
	SATA Mode
	RAID		Set onboard SATA mode to RAID.
	IDE		Set onboard SATA mode to IDE. (Default value)
	AC97 Audio
	Auto		Enable onboard AC'97 audio function. (Default value)
	Disabled		Disable this function.
	USB 1.1 Controller
	Disabled		Disable USB 1.1 controller.
	Enabled		Enable USB 1.1 controller. (Default value)
	USB 2.0 Controller
	Disabled		Disable USB 2.0 controller.
	Enabled		Enable USB 2.0 controller. (Default value)
	USB Keyboard Support
	Enabled		Enable USB keyboard support.
	Disabled		Disable USB keyboard support. (Default value)

GA-8VM800PMD-775 Motherboard

- 36 -

Image 36

Contents GA-8VM800PMD-775 Motherboard GA-8VM800PMD-775 Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8VM800PMD-775 Motherboard Layout VIA775-8VM800PMDBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPU4Mbit flash ROM Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction EnglishATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorFpanel Front Panel Connector Faudio Front Audio Panel Connector PwrledCdin CD in Connector, black Auxin AUX In Connector, whiteSpdifio Spdif In/ Out connector, red Surcen Surround Center Connector, black15 F1USB / F2USB Front USB Connectors Comb Comb ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D1 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeIDE Channel 0/1 Master, Slave IDE Channel 2/3 MasterFloppy 3 Mode Support for Japan Area Drive aHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals IDEOnBoard LAN Boot ROM Parallel Port ModeEPP Mode Select USB Mouse SupportPower Management Setup Acpi OSMouse Power On Resume by AlarmPME Event Wake Up Modem Ring ResumePnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency / Voltage Control Dram Clock AGP OverVoltage ControlDimm OverVoltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Configuring Sata Hard Drives To configure Sata hard drives, follow the steps belowInstall Sata hard drives in your system IDE Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation RAID array, select VIA ATA/ATAPI Host ControllerWindows XP Enter= Continue R=Repair F3=Exit Channel Audio Setup 5 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai