Intel GA-8VM800PMD-775 user manual Load Fail-Safe Defaults, Load Optimized Defaults

Page 44

English

2-8

Load Fail-Safe Defaults

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

`

Standard CMOS Features

Load Fail-Safe Defaults

`

Advanced BIOS Features

Load Optimized Defaults

`

Integrated Peripherals

Set Supervisor Password

`

Power Management Setup

Set User Password

`

PnP/PCI Configurations

Load Fail-Safe DefaultsSave(Y/N)?& ExitN Setup

`

PC Health Status

Exit Without Saving

`

Frequency/Voltage Control

 

ESC: Quit

KLJI: Select Item

F8: Q-Flash

F10: Save & Exit Setup

 

 

Load Fail-Safe Defaults

 

 

 

Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance.

2-9

Load Optimized Defaults

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

`

Standard CMOS Features

Load Fail-Safe Defaults

`

Advanced BIOS Features

Load Optimized Defaults

`

Integrated Peripherals

Set Supervisor Password

`

Power Management Setup

Set User Password

`

PnP/PCI Configurations

Load Optimized DefaultsSave(Y/N)?& ExitN Setup

`

PC Health Status

Exit Without Saving

`

Frequency/Voltage Control

 

ESC: Quit

KLJI: Select Item

F8: Q-Flash

F10: Save & Exit Setup

 

 

Load Optimized Defaults

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects.

GA-8VM800PMD-775 Motherboard

- 44 -

Image 44
Contents GA-8VM800PMD-775 Motherboard GA-8VM800PMD-775 Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8VM800PMD-775 Motherboard Layout VIA775-8VM800PMDBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPU4Mbit flash ROM Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction EnglishATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorFpanel Front Panel Connector Faudio Front Audio Panel Connector PwrledCdin CD in Connector, black Auxin AUX In Connector, whiteSpdifio Spdif In/ Out connector, red Surcen Surround Center Connector, black15 F1USB / F2USB Front USB Connectors Comb Comb ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D1 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeIDE Channel 0/1 Master, Slave IDE Channel 2/3 MasterFloppy 3 Mode Support for Japan Area Drive aHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals IDEOnBoard LAN Boot ROM Parallel Port ModeEPP Mode Select USB Mouse SupportPower Management Setup Acpi OSMouse Power On Resume by AlarmPME Event Wake Up Modem Ring ResumePnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency / Voltage Control Dimm OverVoltage Control Dram ClockAGP OverVoltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewHow to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Install Sata hard drives in your system Configuring Sata Hard DrivesTo configure Sata hard drives, follow the steps below IDE Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation RAID array, select VIA ATA/ATAPI Host ControllerWindows XP Enter= Continue R=Repair F3=Exit Channel Audio Setup 5 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai