Intel GA-8VM800PMD-775 user manual 4Mbit flash ROM

Page 11

Rear Panel I/O		1 PS/2 keyboard port
	1 PS/2 mouse port
		1 parallel port
	1 serial port (COMA)
		1 VGA port
	4 USB 2.0/1.1 ports
		1 RJ-45 port
	3 audio jacks (Line In / Line Out / MIC In)
I/O Control		Winbond W83627 chip
Hardware Monitor		System voltage detection
	CPU / System temperature detection
	CPU / System fan speed detection
	CPU / System fan failure warning
	CPU smart fan control
BIOS		1 4Mbit flash ROM
	Use of licensed AWARD BIOS
Additional Features		Supports @BIOS
		Supports Download Center
		Supports Q-Flash
	Supports EasyTune (only supports Hardware Monitor function) (Note 3)
		Supports Xpress Install
		Supports Xpress Recovery
		Supports Xpress Rescue
Bundle Software		Norton Internet Security (OEM version)
Form Factor		Micro ATX form factor; 24.4cm x 23.3cm

(Note 1) For further CPU support information, please go to GIGABYTE's website.

(Note 2) Use of a Double-Sided memory module (the single chip is 512 Mbit) is required if you wish to install a 1 GB memory module.

(Note 3) EasyTune functions may vary depending on different motherboards.

- 11 -

Hardware Installation

English

Image 11

Contents GA-8VM800PMD-775 Motherboard GA-8VM800PMD-775 Product Manual Classification CopyrightTable of Contents Drivers Installation VIA775-8VM800PMD GA-8VM800PMD-775 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature Summary4Mbit flash ROM Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction English Connectors IntroductionATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorAuxin AUX In Connector, white Cdin CD in Connector, blackSurcen Surround Center Connector, black Spdifio Spdif In/ Out connector, redComb Comb Connector 15 F1USB / F2USB Front USB ConnectorsClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. D1 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 2/3 Master Standard Cmos FeaturesTime IDE Channel 0/1 Master, SlaveMemory Floppy 3 Mode Support for Japan AreaDrive a Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceCPU Enhanced Halt C1E Note CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory Protect NoteIDE Integrated PeripheralsUSB Mouse Support OnBoard LAN Boot ROMParallel Port Mode EPP Mode SelectAcpi OS Power Management SetupModem Ring Resume Mouse Power OnResume by Alarm PME Event Wake UpPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Frequency / Voltage Control Dimm OverVoltage Control Dram ClockAGP OverVoltage Control Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Press F9 during powering on the computer. Text Mode F9 For Xpress RecoveryExit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Install Sata hard drives in your system Configuring Sata Hard DrivesTo configure Sata hard drives, follow the steps below IDE Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation RAID array, select VIA ATA/ATAPI Host ControllerWindows XP Enter= Continue R=Repair F3=Exit 5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device AMI Bios Beep Codes TroubleshootingEnglish English English Taiwan Headquarters Contact UsChina Shanghai