Intel GA-8VM800PMD-775 user manual I/O Back Panel Introduction

Page 16

English

1-6 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

Serial Port

Devices like mouses, modems, and etc. can be connected to Serial port.

VGA Port

Monitor can be connected to VGA port.

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.

LAN Port

The provided Internet connection is fast Ethernet, providing data transfer speeds of 10/100Mbps.

Line In

Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out (Front Speaker Out)

Connect the stereo speakers, earphone or front surround channels to this connector.

MIC In

Microphone can be connected to MIC In jack.

GA-8VM800PMD-775 Motherboard

- 16 -

Image 16
Contents GA-8VM800PMD-775 Motherboard GA-8VM800PMD-775 Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8VM800PMD-775 Motherboard Layout VIA775-8VM800PMDBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPU4Mbit flash ROM Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction EnglishATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorFpanel Front Panel Connector Faudio Front Audio Panel Connector PwrledCdin CD in Connector, black Auxin AUX In Connector, whiteSpdifio Spdif In/ Out connector, red Surcen Surround Center Connector, black15 F1USB / F2USB Front USB Connectors Comb Comb ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D1 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeIDE Channel 0/1 Master, Slave IDE Channel 2/3 MasterFloppy 3 Mode Support for Japan Area Drive aHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals IDEOnBoard LAN Boot ROM Parallel Port ModeEPP Mode Select USB Mouse SupportPower Management Setup Acpi OSMouse Power On Resume by AlarmPME Event Wake Up Modem Ring ResumePnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency / Voltage Control AGP OverVoltage Control Dram ClockDimm OverVoltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewWhat is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Press F9 during powering on the computer. Text ModeRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish To configure Sata hard drives, follow the steps below Configuring Sata Hard DrivesInstall Sata hard drives in your system IDE Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation RAID array, select VIA ATA/ATAPI Host ControllerWindows XP Enter= Continue R=Repair F3=Exit Channel Audio Setup 5 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai