Sanyo PDG-DHT100L owner manual Terminals and Connectors

Page 11

Part Names and Functions

Terminals and Connectors

q

w

e

r

t

y

u

!1

i

!2 o

!0

qUSB CONNECTOR (Series B)

USB connector is used to service the projector.

w5 BNC INPUT JACKS

Connect the component or composite video output signal from video equipment to VIDEO/Y, Pb/Cb, and Pr/Cr jacks or connect the computer output signal (5 BNC Type [Green, Blue, Red, Horiz. Sync, and Vert. Sync.]) to G, B, R, H/V, and V jacks. (pp.20–21)

eD-sub 15-PIN INPUT TERMINAL

Connect computer output (Analog D-sub 15-pin type) to this terminal. (pp.20-21)

rMONITOR OUT TERMINAL

This terminal can be used to output the incoming analog RGB, component, or composite video out signals from INPUT 1-2 terminal to the other monitor. (pp.20-21)

tDVI INPUT TERMINAL

Connect computer output (Digital/DVI-D type) to this terminal. (p.20)

HDTV (HDCP Compatible) signal can be also connected. (p.21)

yHDMI

Connect the HDMI output signal from video equipment to this terminal. (p.21)

uS-VIDEO INPUT JACK

Connect the S-VIDEO output signal from video equipment to this jack. (p.21)

iSERIAL PORT IN TERMINAL

If you control the projector by computer, you must connect a cable (not supplied) from your computer to this terminal.

oSERIAL PORT OUT TERMINAL

This terminal outputs signal from SERIAL PORT IN. More than two projectors can be controlled with one computer by connecting SERIAL PORT IN of another projector to this terminal.

!0R/C JACK

When using the wired remote control, connect the wired remote control to this jack with a remote control cable (not supplied).

!1LAN port

Connecting the LAN cable. See the owner's manual of the Network Board for details.

!2Serial port

This is used when controlling the external equipment via the network.

11

Image 11
Contents Model PDG-DHT100L Features and Design Table of Contents Risk of Electric Shock Do not Open To The OwnerSafety Instructions Top Panel Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsMoving the Projector Canadian Radio Interference Regulations AC Power Cord for the United States and CanadaAC Power Cord for the United Kingdom ComplianceBack Part Names and FunctionsFront!0 Terminals and Connectors Side Control Side Control and IndicatorsIndicators Remote Control Wired Remote Control Remote Control Battery InstallationRemote Control Receivers and Operating Range Remote Control Code Positioning Projector InstallationLens Installation When the lens is shifted to bottom Lens Shift AdjustmentPicture Level and Pitch Adjustment When the lens is shifted to topTerminals of Projector Replacement of TerminalTerminals of the projector Connecting to ComputerCables used for connection Projector Connecting to Video EquipmentMonitor Out Signal Table Attaching the Cable Cover For the U..S..A.. and Canada For Continental Europe Connecting the AC Power CordFor the U..K Enter a PIN code What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector Unplug the AC power cord from the AC outletOn-Screen Menu How to Operate the On-Screen MenuRemote Control Side ControlMenu Bar Operating with Projector Control Information Operating with Remote Control Image ADJ.. button Timer buttonShutter button Filter buttonSide Control Operation Remote Control OperationInput Selection InputInput Menu When Selecting the Input 1 with DVI/D-sub 15 terminalsComputer Input Source Selection Menu OperationPb/Cb, Pr/Cr Video Input Source SelectionRGB Scart RGB AV HdcpSelecting Computer System Manually Computer InputComputer System Selection Automatic Multi-Scan SystemDirect Operation Auto PC AdjustmentTo store the adjusted parameters PC Adjust MenuManual PC Adjustment To store the adjusted data ResetMode free To clear the adjusted dataImage Image Level SelectionStandard Real Dynamic Image1 Image SEL.. button StandardScreen Menu Screen Size AdjustmentDigital zoom + KeystoneCeiling RearPb/Cb, Pr/Cr Jacks Video InputVideo System Selection Video Jack or S-Video JackStandard Cinema Dynamic Image1 Image SEL.. button Natural Wide ZoomKeystone Picture Image Image AdjustmentImage Adjust Menu Pointer ModeDEL Color MMenu Color PaletteGamma White balance Red/Green/BlueOffset Red/Green/Blue SharpnessSetting SettingLamp life control Lamp modeBackground Lamp controlPicture in Picture Color matching Edge blendingDynamicBlack Advanced color matchingCapture Hdmi setupLogo Logo selectChange the Logo PIN code Change the Logo PIN code lock settingEnter a Logo PIN code Filter control Remote controlTo change the code for the remote control To reset the code for the remote controlOn start Power managementKey lock PIN code lock Security Key lockPIN code lock SecurityEnter a PIN code Change the PIN Code Lock settingChange the PIN code lock setting Change the PIN CodeManagement ShutterProtection Test pattern Factory defaultFilter counter Filter Instructions Maintenance and CareReplacing the Filter Cartridge Reset the filter counter and the scroll counter p.64Service Parts Code 610 334 Scroll counter Filter counterLamp Status Display Lamp 1/2 Replace IndicatorsLamp Mode Changeover Lamp ManagementLamp 1 / 2 Replace indicators Lamp ReplacementIndicators Model No.. of your projector Replacement Lamp Type NoOptional Color Wheel Installation Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below Lamp indicator lights on and other indicators blinkAppendix TroubleshootingAppendix Power is turned off Network Information Image AdjustMenu Tree Computer Input/Video InputScreen PC AdjustSystem Image SelectSetting Projector is operating normally Indicators and Projector ConditionLamp Replace 1 Projector is detecting abnormal conditionFig..4 Display Compatible Computer SpecificationsON-SCREEN Resolution Freq..kHz Freq..HzKHz FreqOn-Board List of Picture in PictureTechnical Specifications POA-MD23ADI Optional PartsOutput Configurations of TerminalsControl Port Connector D-sub 9 pin InputLogo PIN Code Lock No PIN Code Number MemoPIN Code Lock No Dimensions Example Functional Execution CommandSerial Control Interface OperationStatus Read Command KT5AL-A

PDG-DHT100L specifications

The Sanyo PDG-DHT100L is a versatile projector that caters to a variety of presentation needs, making it an excellent choice for both business and educational settings. Known for its bright and vibrant image quality, this projector utilizes advanced technologies to deliver high-performance visuals.

One of the standout features of the Sanyo PDG-DHT100L is its impressive brightness rating, which typically exceeds 3000 lumens. This high brightness capability ensures that presentations remain clear and visible in various lighting conditions, from dimly lit conference rooms to brightly lit classrooms. Coupled with a high contrast ratio, the projector produces sharp images with deep blacks and bright whites, enhancing the overall viewing experience.

The PDG-DHT100L employs DLP (Digital Light Processing) technology, known for its reliability and excellent color reproduction. DLP projectors produce smooth motion and consistent brightness across the entire image, making them ideal for displaying detailed graphics, videos, and dynamic presentations. The use of a color wheel contributes to optimal color accuracy, resulting in vivid and true-to-life colors.

Connectivity is another area where the Sanyo PDG-DHT100L shines. It offers multiple input options, including HDMI, VGA, and composite inputs, allowing users to connect a range of devices such as laptops, tablets, and media players seamlessly. This flexibility makes it easy to integrate the projector into existing setups or to utilize it for various types of presentations without the need for additional adapters.

Portability is a key characteristic of the Sanyo PDG-DHT100L. Weighing relatively light compared to other projectors in its class, it is designed for easy transport between different locations. This feature is especially beneficial for professionals who need to deliver presentations at multiple sites or educators moving from classroom to classroom.

Additionally, the Sanyo PDG-DHT100L encompasses a robust lamp life, often exceeding 4000 hours in standard mode, which reduces maintenance costs and downtime. The easy-to-replace lamp is designed for convenience, ensuring that users can quickly resume presentations after a lamp change.

In summary, the Sanyo PDG-DHT100L combines brightness, color accuracy, and portability, making it a reliable choice for anyone in need of a high-quality projector. Its advanced DLP technology, multiple connectivity options, and impressive lamp life further establish it as a valuable asset for both professional and educational purposes.