Sanyo PDG-DHT100L owner manual Appendix

Page 72

Appendix

 

– The end of lamp life is approaching. Replace the lamp with a new one promptly.

appears on the screen

(See page 66)

 

 

 

 

– The filter is out of scroll. Replace the filter cartridge with a new one promptly.

 

(See pages 62-63)

appears on the screen

 

 

– Adjust the focus of the projector.

 

– Check Projection Lens to see if it needs cleaning.

The image is out of focus.

✔Note: Moving the projector from a cool temperature location to a warm temperature

location may result in moisture condensation on Projection Lens. In such cases,

 

leave the projector OFF and wait until condensation evaporates.

 

– Projecting from excessive slant angle to the screen may cause keystone distortion and

 

partial imperfect focus.

 

 

 

– Check if “Contrast” or “Brightness” are adjusted properly. (See page 46)

 

– Check if “Image level” is selected properly. (See pages 39, 43)

The image is not bright

– Check the Lamp control function. ( See “SETTING” section on page 50)

– Check the Lamp 1/2 replace indicators. If it lights, the end of lamp life is approaching.

enough.

Replace the lamp with a new one promptly. (See page 66)

 

 

– The image is darker when 1 lamp mode is selected, compared with 2 lamp mode.

 

Check the lamp mode at SETTING section on page 50.

 

 

The color is strange.

– Check the Input signal, color system, video system, or computer system mode.

 

 

The image is Left/Right

– Check the Ceiling / Rear function. (See pages 41, 45)

reversed.

 

The image is Top/Bottom

– Check the Ceiling function. (See pages 41, 45)

reversed.

 

The image is distorted or

– Check “PC Adjust” menu or “ Screen” menu and adjust them.

runs off.

 

Auto PC adjustment

– Check the Input signal. Auto PC Adjustment function cannot work when 480p, 575p,

720p, 480i, 575i, 1035i, 1080p, or 1080i is selected or when the digital signal is input

function does not work.

into DVI terminal. (See page 36)

 

 

 

Some displays are not

– Check the Display function (see page 49).

seen during the operation.

The setting does not

– Make sure you selected “Store” after adjusting settings. Some settings cannot be

remain after turning off

stored if not registered with “Store”.

power.

 

Power management

– Power management function cannot work while “Freeze” function is running or the

function does not work.

shutter is closed.

Image disappears

– Check the power management function in the Setting. The power management is set

automatically.

to "On" at the factory.

Capture function does not

– Check the connection to see if there is signal.

work.

 

Some menus cannot be

– Each of the Video Input and Computer Input has a limit on selectable menus.

selected.

 

72

Page 71 Page 73
Image 72
Page 71 Page 73
Contents Model PDG-DHT100L Features and Design Table of Contents To The Owner Risk of Electric Shock Do not OpenSafety Instructions Air Circulation Top PanelInstalling the Projector in Proper Directions Positioning PrecautionsMoving the Projector AC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Canadian Radio Interference RegulationsPart Names and Functions Front!0Back Terminals and Connectors Side Control and Indicators Side ControlIndicators Remote Control Remote Control Battery Installation Remote Control Receivers and Operating RangeWired Remote Control Remote Control Code Installation Lens InstallationPositioning Projector Lens Shift Adjustment Picture Level and Pitch AdjustmentWhen the lens is shifted to top When the lens is shifted to bottomReplacement of Terminal Terminals of ProjectorConnecting to Computer Cables used for connectionTerminals of the projector Connecting to Video Equipment Monitor Out Signal TableProjector Attaching the Cable Cover Connecting the AC Power Cord For the U..KFor the U..S..A.. and Canada For Continental Europe What is PIN code? Basic OperationTurning On the Projector Enter a PIN codeUnplug the AC power cord from the AC outlet Turning Off the ProjectorHow to Operate the On-Screen Menu Remote ControlSide Control On-Screen MenuMenu Bar Operating with Projector Control Information Operating with Remote Control Timer button Shutter buttonFilter button Image ADJ.. buttonRemote Control Operation Input SelectionInput Side Control OperationWhen Selecting the Input 1 with DVI/D-sub 15 terminals Computer Input Source SelectionMenu Operation Input MenuVideo Input Source Selection RGB ScartRGB AV Hdcp Pb/Cb, Pr/CrComputer Input Computer System SelectionAutomatic Multi-Scan System Selecting Computer System ManuallyAuto PC Adjustment To store the adjusted parametersPC Adjust Menu Direct OperationManual PC Adjustment Reset Mode freeTo clear the adjusted data To store the adjusted dataImage Level Selection Standard Real Dynamic Image1 Image SEL.. buttonStandard ImageScreen Size Adjustment Screen MenuKeystone CeilingRear Digital zoom +Video Input Video System SelectionVideo Jack or S-Video Jack Pb/Cb, Pr/Cr JacksStandard Cinema Dynamic Image1 Image SEL.. button Zoom Natural WideKeystone Image Adjustment Image Adjust MenuPointer Mode Picture ImageColor M MenuColor Palette DELWhite balance Red/Green/Blue Offset Red/Green/BlueSharpness GammaSetting SettingLamp mode BackgroundLamp control Lamp life controlPicture in Picture Edge blending Color matchingAdvanced color matching DynamicBlackHdmi setup LogoLogo select CaptureChange the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code Remote control To change the code for the remote controlTo reset the code for the remote control Filter controlPower management On startSecurity Key lock PIN code lockSecurity Key lock PIN code lockChange the PIN Code Lock setting Change the PIN code lock settingChange the PIN Code Enter a PIN codeShutter ProtectionManagement Factory default Filter counterTest pattern Maintenance and Care Filter InstructionsReset the filter counter and the scroll counter p.64 Service Parts Code 610 334Replacing the Filter Cartridge Filter counter Scroll counterLamp 1/2 Replace Indicators Lamp Mode ChangeoverLamp Management Lamp Status DisplayLamp Replacement IndicatorsLamp 1 / 2 Replace indicators Replacement Lamp Type No Model No.. of your projectorOptional Color Wheel Installation Cleaning the Projection Lens Cleaning the Projector CabinetLamp indicator lights on and other indicators blink Then check the matters belowTroubleshooting AppendixAppendix Power is turned off Information Image Adjust Menu TreeComputer Input/Video Input NetworkPC Adjust SystemImage Select ScreenSetting Indicators and Projector Condition Projector is operating normallyProjector is detecting abnormal condition Lamp Replace 1Fig..4 Compatible Computer Specifications ON-SCREEN ResolutionFreq..kHz Freq..Hz DisplayFreq KHzList of Picture in Picture On-BoardTechnical Specifications Optional Parts POA-MD23ADIConfigurations of Terminals Control Port Connector D-sub 9 pinInput OutputPIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Dimensions Functional Execution Command Serial Control InterfaceOperation ExampleStatus Read Command KT5AL-A

PDG-DHT100L specifications

The Sanyo PDG-DHT100L is a versatile projector that caters to a variety of presentation needs, making it an excellent choice for both business and educational settings. Known for its bright and vibrant image quality, this projector utilizes advanced technologies to deliver high-performance visuals.

One of the standout features of the Sanyo PDG-DHT100L is its impressive brightness rating, which typically exceeds 3000 lumens. This high brightness capability ensures that presentations remain clear and visible in various lighting conditions, from dimly lit conference rooms to brightly lit classrooms. Coupled with a high contrast ratio, the projector produces sharp images with deep blacks and bright whites, enhancing the overall viewing experience.

The PDG-DHT100L employs DLP (Digital Light Processing) technology, known for its reliability and excellent color reproduction. DLP projectors produce smooth motion and consistent brightness across the entire image, making them ideal for displaying detailed graphics, videos, and dynamic presentations. The use of a color wheel contributes to optimal color accuracy, resulting in vivid and true-to-life colors.

Connectivity is another area where the Sanyo PDG-DHT100L shines. It offers multiple input options, including HDMI, VGA, and composite inputs, allowing users to connect a range of devices such as laptops, tablets, and media players seamlessly. This flexibility makes it easy to integrate the projector into existing setups or to utilize it for various types of presentations without the need for additional adapters.

Portability is a key characteristic of the Sanyo PDG-DHT100L. Weighing relatively light compared to other projectors in its class, it is designed for easy transport between different locations. This feature is especially beneficial for professionals who need to deliver presentations at multiple sites or educators moving from classroom to classroom.

Additionally, the Sanyo PDG-DHT100L encompasses a robust lamp life, often exceeding 4000 hours in standard mode, which reduces maintenance costs and downtime. The easy-to-replace lamp is designed for convenience, ensuring that users can quickly resume presentations after a lamp change.

In summary, the Sanyo PDG-DHT100L combines brightness, color accuracy, and portability, making it a reliable choice for anyone in need of a high-quality projector. Its advanced DLP technology, multiple connectivity options, and impressive lamp life further establish it as a valuable asset for both professional and educational purposes.
Top Page Image Contents