Sanyo PDG-DHT100L Serial Control Interface, Operation, Functional Execution Command, Example

Page 88

Appendix

Serial Control Interface

This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port.

Operation

1

Connect a RS-232C serial cross cable to SERIAL

PORT IN on the projector and serial port on the PC.

 

(See p.11)

2

Launch a communication software provided with PC

 

and setup the communication condition as follows:

3

Type the command for controlling the projector and

 

then enter the "Enter" key.

Example

When you want to change the input to INPUT 2, Type 'C' '0' '6' 'Enter'.

Baud rate

: 9600 / 19200 bps

Parity check

: none

Stop bit

: 1

Flow control

: none

Data bit

: 8

 

 

Note:

•The default of the baud rate is set to 19200 bps. If an error occurs in the communication, change the serial port and the communication speed (baud rate).

•Enter with ASCII 64-byte capital characters and one- byte characters.

Functional Execution Command

Format

The command is sent from PC to the projector with the format below;

'C' [Command] 'CR'

Command: two characters (refer to the command table below.

-The projector decodes the command and returns the 'ACK' with the format below;

'ACK' 'CR'

-When the projector cannot decode the command, it returns with format below.

‘?’ ‘CR’

Command

Function

C00

Turn the projector ON

C01

Turn the projector OFF

(immediately OFF)

 

C05

Select Input 1

C06

Select Input 2

C07

Select Input 3

C08

Select Input 4

C0D

Video mute ON

C0E

Video mute OFF

C0F

Aspect 4:3

C10

Aspect 16:9

C1C

Menu ON

C1D

Menu OFF

C3A

Pointer RIGHT

Command

Function

C3B

Pointer LEFT

C3C

Pointer UP

C3D

Pointer DOWN

C3F

Enter

C46

Zoom DOWN

C47

Zoom UP

C4A

Focus DOWN

C4B

Focus UP

C5D

Lens shift UP

C5E

Lens shift DOWN

C5F

Lens shift LEFT

C60

Lens shift RIGHT

C89

Auto PC Adj.

C8E

Keystone UP

C8F

Keystone DOWN

C90

Keystone RIGHT

C91

Keystone LEFT

88

Image 88
Contents Model PDG-DHT100L Features and Design Table of Contents To The Owner Risk of Electric Shock Do not OpenSafety Instructions Air Circulation Top PanelInstalling the Projector in Proper Directions Positioning PrecautionsMoving the Projector AC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Canadian Radio Interference RegulationsFront!0 Part Names and FunctionsBack Terminals and Connectors Side Control and Indicators Side ControlIndicators Remote Control Remote Control Receivers and Operating Range Remote Control Battery InstallationWired Remote Control Remote Control Code Lens Installation InstallationPositioning Projector Lens Shift Adjustment Picture Level and Pitch AdjustmentWhen the lens is shifted to top When the lens is shifted to bottomReplacement of Terminal Terminals of ProjectorCables used for connection Connecting to ComputerTerminals of the projector Monitor Out Signal Table Connecting to Video EquipmentProjector Attaching the Cable Cover For the U..K Connecting the AC Power CordFor the U..S..A.. and Canada For Continental Europe What is PIN code? Basic OperationTurning On the Projector Enter a PIN codeUnplug the AC power cord from the AC outlet Turning Off the ProjectorHow to Operate the On-Screen Menu Remote ControlSide Control On-Screen MenuMenu Bar Operating with Projector Control Information Operating with Remote Control Timer button Shutter buttonFilter button Image ADJ.. buttonRemote Control Operation Input SelectionInput Side Control OperationWhen Selecting the Input 1 with DVI/D-sub 15 terminals Computer Input Source SelectionMenu Operation Input MenuVideo Input Source Selection RGB ScartRGB AV Hdcp Pb/Cb, Pr/CrComputer Input Computer System SelectionAutomatic Multi-Scan System Selecting Computer System ManuallyAuto PC Adjustment To store the adjusted parametersPC Adjust Menu Direct OperationManual PC Adjustment Reset Mode freeTo clear the adjusted data To store the adjusted dataImage Level Selection Standard Real Dynamic Image1 Image SEL.. buttonStandard ImageScreen Size Adjustment Screen MenuKeystone CeilingRear Digital zoom +Video Input Video System SelectionVideo Jack or S-Video Jack Pb/Cb, Pr/Cr JacksStandard Cinema Dynamic Image1 Image SEL.. button Zoom Natural WideKeystone Image Adjustment Image Adjust MenuPointer Mode Picture ImageColor M MenuColor Palette DELWhite balance Red/Green/Blue Offset Red/Green/BlueSharpness GammaSetting SettingLamp mode BackgroundLamp control Lamp life controlPicture in Picture Edge blending Color matchingAdvanced color matching DynamicBlackHdmi setup LogoLogo select CaptureEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code Remote control To change the code for the remote controlTo reset the code for the remote control Filter controlPower management On startSecurity Key lock PIN code lockSecurity Key lock PIN code lockChange the PIN Code Lock setting Change the PIN code lock settingChange the PIN Code Enter a PIN codeProtection ShutterManagement Filter counter Factory defaultTest pattern Maintenance and Care Filter InstructionsService Parts Code 610 334 Reset the filter counter and the scroll counter p.64Replacing the Filter Cartridge Filter counter Scroll counterLamp 1/2 Replace Indicators Lamp Mode ChangeoverLamp Management Lamp Status DisplayIndicators Lamp ReplacementLamp 1 / 2 Replace indicators Replacement Lamp Type No Model No.. of your projectorOptional Color Wheel Installation Cleaning the Projection Lens Cleaning the Projector CabinetLamp indicator lights on and other indicators blink Then check the matters belowTroubleshooting AppendixAppendix Power is turned off Information Image Adjust Menu TreeComputer Input/Video Input NetworkPC Adjust SystemImage Select ScreenSetting Indicators and Projector Condition Projector is operating normallyProjector is detecting abnormal condition Lamp Replace 1Fig..4 Compatible Computer Specifications ON-SCREEN ResolutionFreq..kHz Freq..Hz DisplayFreq KHzList of Picture in Picture On-BoardTechnical Specifications Optional Parts POA-MD23ADIConfigurations of Terminals Control Port Connector D-sub 9 pinInput OutputPIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Dimensions Functional Execution Command Serial Control InterfaceOperation ExampleStatus Read Command KT5AL-A

PDG-DHT100L specifications

The Sanyo PDG-DHT100L is a versatile projector that caters to a variety of presentation needs, making it an excellent choice for both business and educational settings. Known for its bright and vibrant image quality, this projector utilizes advanced technologies to deliver high-performance visuals.

One of the standout features of the Sanyo PDG-DHT100L is its impressive brightness rating, which typically exceeds 3000 lumens. This high brightness capability ensures that presentations remain clear and visible in various lighting conditions, from dimly lit conference rooms to brightly lit classrooms. Coupled with a high contrast ratio, the projector produces sharp images with deep blacks and bright whites, enhancing the overall viewing experience.

The PDG-DHT100L employs DLP (Digital Light Processing) technology, known for its reliability and excellent color reproduction. DLP projectors produce smooth motion and consistent brightness across the entire image, making them ideal for displaying detailed graphics, videos, and dynamic presentations. The use of a color wheel contributes to optimal color accuracy, resulting in vivid and true-to-life colors.

Connectivity is another area where the Sanyo PDG-DHT100L shines. It offers multiple input options, including HDMI, VGA, and composite inputs, allowing users to connect a range of devices such as laptops, tablets, and media players seamlessly. This flexibility makes it easy to integrate the projector into existing setups or to utilize it for various types of presentations without the need for additional adapters.

Portability is a key characteristic of the Sanyo PDG-DHT100L. Weighing relatively light compared to other projectors in its class, it is designed for easy transport between different locations. This feature is especially beneficial for professionals who need to deliver presentations at multiple sites or educators moving from classroom to classroom.

Additionally, the Sanyo PDG-DHT100L encompasses a robust lamp life, often exceeding 4000 hours in standard mode, which reduces maintenance costs and downtime. The easy-to-replace lamp is designed for convenience, ensuring that users can quickly resume presentations after a lamp change.

In summary, the Sanyo PDG-DHT100L combines brightness, color accuracy, and portability, making it a reliable choice for anyone in need of a high-quality projector. Its advanced DLP technology, multiple connectivity options, and impressive lamp life further establish it as a valuable asset for both professional and educational purposes.