Sanyo PDG-DHT100L owner manual Power is turned off

Page 73

Appendix

The power is turned off

– Power management function runs by initial setting. Check “SETTING” section on page

automatically.

57.

 

 

You cannot operate with

– The side control is not available If the side control is locked at “Key lock” under

the side control.

“Security” of SETTING section. Please check “SETTING” section on page 58.

 

 

 

– Check the batteries.

 

– Check if the RC sensor is set properly. (See page 56)

 

– Make sure no obstruction is between the projector and remote control.

 

– Make sure you are not too far from the projector when using the remote control.

The Remote Control does

Maximum operating range is 16.4’ (5m).

– Make sure that the remote control code conforms to the projector’s code.

not work.

(See “SETTING” section on page 56.)

 

– Make sure the reset switch in the compartment lid on back of the remote control is set

 

to use position.

 

– Unlock the Key lock function for the remote control. (See page 58)

 

– Wireless remote control does not work when the remote control cable is connected to

 

the projector. (See page 15)

Indicators blinks or lights.

– Check the status of the projector with referring to “ INDICATORS AND PROJECTOR

 

CONDITION” on pages 77-79.

 

 

 

– Your operation is invalid. Operate correctly.

appears on the screen

 

 

 

Unable to unlock the Logo

 

PIN code lock, Security

Contact the dealer where you purchased the projector or the service center.

key lock or Security PIN

 

code lock.

 

 

 

Forget the Logo PIN code

Contact the dealer where you purchased the projector or the service center.

or Security PIN code.

 

 

 

WARNING:

High voltages are used to operate this projector.. Do not attempt to open the cabinet..

If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem. We will advise you how to obtain service.

This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty, and electrical hazards.

The CE Mark is a Directive conformity mark of the European Community (EC).

Pixelworks ICs used.

73

Image 73
Contents Model PDG-DHT100L Features and Design Table of Contents Risk of Electric Shock Do not Open To The OwnerSafety Instructions Top Panel Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsMoving the Projector AC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Canadian Radio Interference RegulationsFront!0 Part Names and FunctionsBack Terminals and Connectors Side Control Side Control and IndicatorsIndicators Remote Control Remote Control Receivers and Operating Range Remote Control Battery InstallationWired Remote Control Remote Control Code Lens Installation InstallationPositioning Projector Picture Level and Pitch Adjustment Lens Shift AdjustmentWhen the lens is shifted to top When the lens is shifted to bottomTerminals of Projector Replacement of TerminalCables used for connection Connecting to ComputerTerminals of the projector Monitor Out Signal Table Connecting to Video EquipmentProjector Attaching the Cable Cover For the U..K Connecting the AC Power CordFor the U..S..A.. and Canada For Continental Europe Basic Operation What is PIN code?Turning On the Projector Enter a PIN codeTurning Off the Projector Unplug the AC power cord from the AC outletRemote Control How to Operate the On-Screen MenuSide Control On-Screen MenuMenu Bar Operating with Projector Control Information Operating with Remote Control Shutter button Timer buttonFilter button Image ADJ.. buttonInput Selection Remote Control OperationInput Side Control OperationComputer Input Source Selection When Selecting the Input 1 with DVI/D-sub 15 terminalsMenu Operation Input MenuRGB Scart Video Input Source SelectionRGB AV Hdcp Pb/Cb, Pr/CrComputer System Selection Computer InputAutomatic Multi-Scan System Selecting Computer System ManuallyTo store the adjusted parameters Auto PC AdjustmentPC Adjust Menu Direct OperationManual PC Adjustment Mode free ResetTo clear the adjusted data To store the adjusted dataStandard Real Dynamic Image1 Image SEL.. button Image Level SelectionStandard ImageScreen Menu Screen Size AdjustmentCeiling KeystoneRear Digital zoom +Video System Selection Video InputVideo Jack or S-Video Jack Pb/Cb, Pr/Cr JacksStandard Cinema Dynamic Image1 Image SEL.. button Natural Wide ZoomKeystone Image Adjust Menu Image AdjustmentPointer Mode Picture ImageMenu Color MColor Palette DELOffset Red/Green/Blue White balance Red/Green/BlueSharpness GammaSetting SettingBackground Lamp modeLamp control Lamp life controlPicture in Picture Color matching Edge blendingDynamicBlack Advanced color matchingLogo Hdmi setupLogo select CaptureEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code To change the code for the remote control Remote controlTo reset the code for the remote control Filter controlOn start Power managementPIN code lock Security Key lockSecurity Key lock PIN code lockChange the PIN code lock setting Change the PIN Code Lock settingChange the PIN Code Enter a PIN codeProtection ShutterManagement Filter counter Factory defaultTest pattern Filter Instructions Maintenance and CareService Parts Code 610 334 Reset the filter counter and the scroll counter p.64Replacing the Filter Cartridge Scroll counter Filter counterLamp Mode Changeover Lamp 1/2 Replace IndicatorsLamp Management Lamp Status DisplayIndicators Lamp ReplacementLamp 1 / 2 Replace indicators Model No.. of your projector Replacement Lamp Type NoOptional Color Wheel Installation Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below Lamp indicator lights on and other indicators blinkAppendix TroubleshootingAppendix Power is turned off Menu Tree Information Image AdjustComputer Input/Video Input NetworkSystem PC AdjustImage Select ScreenSetting Projector is operating normally Indicators and Projector ConditionLamp Replace 1 Projector is detecting abnormal conditionFig..4 ON-SCREEN Resolution Compatible Computer SpecificationsFreq..kHz Freq..Hz DisplayKHz FreqOn-Board List of Picture in PictureTechnical Specifications POA-MD23ADI Optional PartsControl Port Connector D-sub 9 pin Configurations of TerminalsInput OutputPIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Dimensions Serial Control Interface Functional Execution CommandOperation ExampleStatus Read Command KT5AL-A

PDG-DHT100L specifications

The Sanyo PDG-DHT100L is a versatile projector that caters to a variety of presentation needs, making it an excellent choice for both business and educational settings. Known for its bright and vibrant image quality, this projector utilizes advanced technologies to deliver high-performance visuals.

One of the standout features of the Sanyo PDG-DHT100L is its impressive brightness rating, which typically exceeds 3000 lumens. This high brightness capability ensures that presentations remain clear and visible in various lighting conditions, from dimly lit conference rooms to brightly lit classrooms. Coupled with a high contrast ratio, the projector produces sharp images with deep blacks and bright whites, enhancing the overall viewing experience.

The PDG-DHT100L employs DLP (Digital Light Processing) technology, known for its reliability and excellent color reproduction. DLP projectors produce smooth motion and consistent brightness across the entire image, making them ideal for displaying detailed graphics, videos, and dynamic presentations. The use of a color wheel contributes to optimal color accuracy, resulting in vivid and true-to-life colors.

Connectivity is another area where the Sanyo PDG-DHT100L shines. It offers multiple input options, including HDMI, VGA, and composite inputs, allowing users to connect a range of devices such as laptops, tablets, and media players seamlessly. This flexibility makes it easy to integrate the projector into existing setups or to utilize it for various types of presentations without the need for additional adapters.

Portability is a key characteristic of the Sanyo PDG-DHT100L. Weighing relatively light compared to other projectors in its class, it is designed for easy transport between different locations. This feature is especially beneficial for professionals who need to deliver presentations at multiple sites or educators moving from classroom to classroom.

Additionally, the Sanyo PDG-DHT100L encompasses a robust lamp life, often exceeding 4000 hours in standard mode, which reduces maintenance costs and downtime. The easy-to-replace lamp is designed for convenience, ensuring that users can quickly resume presentations after a lamp change.

In summary, the Sanyo PDG-DHT100L combines brightness, color accuracy, and portability, making it a reliable choice for anyone in need of a high-quality projector. Its advanced DLP technology, multiple connectivity options, and impressive lamp life further establish it as a valuable asset for both professional and educational purposes.