Hitachi 8880R manual Front Panel Detail

Page 10
Figure 4 Front Panel Detail

Ch 1: Hardware

Item

Feature

 

Description

I

Menu Switch

This switch can select information and options that are displayed on the system’s

 

 

LCD.

 

 

 

J

Power LED

When illuminated it shows that the system power is on.

 

 

 

K

Access LED

When illuminated it shows that SCSI devices are being accessed.

 

 

 

L

Buzzer Stop

Press this button to turn off the buzzer alarm. This buzzer does not necessarily

 

 

indicate system error, it may be in a warning state.

 

 

 

M

Warning LED (yellow)

When illuminated it indicates one of the following recoverable errors:

 

 

This is only for redundancy cases

 

 

•

ECC 1 bit

 

 

•

CPU error

 

 

•

Memory Bus error

 

 

•

HDD error

 

 

•

Temperature is high

 

 

•

Fan failure

 

 

•

Power Supply failure

 

 

 

N

Reset

This Reset is for system maintenance only, and is not a Hardware Reset Switch.

 

 

 

O

Error LED (red)

When illuminated it indicates one of the following serious statuses:

•ECC 2 bit

•CPU error

•HDD error

•Temperature is abnormal

•Fan failure

•Power Supply failure

•PCI slot error

•ISA slot error

A

B

C

D

E

F

G

Green

 

 

 

 

 

 

Red

H

I

J

K L M

N O

 

Figure 4 Front Panel Detail

6

Hitachi VisionBase 8880R Server

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Hitachi VisionBase 8880R Server Product GuideDisclaimer CopyrightTrademarks Issue Date November Part Number 202-85031-01-Rev AContents 3 Error Information POST Error System Beeps 1 Hardware System SpecificationsSystem Overview 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSI Ch 1 Hardware Figure 1 Accessing the Power Supplies Powering-On the SystemFigure 2 Accessing the Power Supplies Figure 3 P/S Receptacle and On/Off Switch Front PanelFigure 4 Front Panel Detail Figure 5 Back Panel Detail Figure 6 Direct Boot Switch DetailBack Panel Detail AWarnings and Cautions Removing the Server Panels and Accessing Its ComponentsSafety Guidelines Tools and Supplies You NeedAccessing the PCI Slots Figure 7 Accessing the Option SlotsPCI/ISA Option Boards Figure 8 Option SlotsSCSI SCA Hard Disk Drives Figure 9 Accessing the Hard Disk DrivesHard Disk Drives Figure 10 Hard Disk Drive BaysInstalling/Swapping a HDD Figure 11 Removing/Installing a HDDFigure 12 Mounting the HDD Carrier Optional DevicesHDD HDD Position Pins HDD Carrier 4 Mounting Screws Figure 14 CPU/VRM Installation Detail Figure 13 Memory and CPU SlotsMemory Figure 15 Memory Board Slot Location The system supports the following specifications for memory DIMMsVRM #3 Jumper SettingsFigure 16 System Board Default Jumper Settings VRM #4Figure 17 I/O Board Switch Settings Flow of System Environment Setting 2 System Environment SettingBefore Operations What You Can Do with the System Environment Setting Outline of the Setup MenuNotes on Use Outline of ISA Configuration Utility ICUSetting for Each Board PCI BoardSetup Menu Flow of the Setup Menu OperationStarting the Setup Menu Figure 18 Entering Setup MenuConfiguration of the Setup Menu Screen Setup Menu ScreenFigure 19 Setup Menu Screen Configuration Operating the Keys on the Setup Menu In the Setup Menu, the following key operations are allowedWhat You Can Do on the Main Menu Steps for Setting the Setup MenuFigure 20 Main Menu Screen Legacy Diskette A,B System Time and System DatePrimary Master Slave What You Can Do on the Advanced Menu Reset Configuration DataExecute ROM Diagnostic Unsupported Network serverSelect Resources PCI ConfigurationI/O Device Configuration Current ResourcesLocal Bus IDE adapter Parallel portFloppy disk controller PS/2 MouseConsole Redirection Unsupported Ext MP Configuration TableEnable memory gap I/O APIC ModeSpeaker Volume WinNT 4.0 Install ModeLarge Disk Access Mode Unsupported Caching Above 4GBSet Supervisor Password Supervisor Password isUser Password is Set User PasswordFigure 23 Boot Menu Screen What You Can Do on the Boot menuHard Drive IDE Hard Disk Drive Exit Discarding Changes What You Can Do on the Exit MenuExit Saving Changes Figure 24 Exit Menu ScreenLoad Setup Defaults ISA Configuration Utility ICUNotes on the Setup Menu Discard ChangesBackup for ICU Disk Flow of Operation with the ICUSpace System ResourcesStarting the ICU Do not remove ICU DISK2 before the ICU terminatesOperating the ICU How to Use HelpICU Screen Figure 25 ICU ScreenExiting the ICU Checking Resource Status Checking Resources Used by the SystemAdding an Extended Board Checking Resources for Extended Boards6. A dialog box for confirmation is displayed. Choose OK Settings for Each Resource Changing the Settings in Extended BoardsReserving I/O Port Addresses Removing an Extended Board Reserving Resources In Use from an ISA Board When ICU Program Disk Has Been DestroyedNOTE Unknown Card is displayed for RAID controller PC-CA7112 Restoring Configuration Information Lock/Unlock CardErrors and Countermeasures Restrictions on the ICU Returning the ICU Settings to Defaults Returning the Settings to DefaultsReturning the Settings of the Setup Information to Defaults List of Utility SettingsFixed Configuration Ch 2 System Environment SettingSymbios Logic SCSI Configuration Utilities This table defines the SCSI Select factory default settingsCh 3 Error Information 3 Error InformationPOST Error Hitachi VisionBase 8880RSystem Beeps 4 NT Drivers and Limitations Installing Windows NT2. Select Advanced Menu-Windows NT 4.0 Install Mode Windows NT Driver RecommendationsCh 4 NT Drivers and Limitations Environment Specification 5 Related Document and SpecificationRelated Document Ch 5 Related Document and Specification Hitachi VisionBase 8880R
Top Page Image Contents