Hitachi 8880R manual Checking Resource Status, Checking Resources Used by the System

Page 45

Checking Resource Status

Ch 2: System Environment Setting

Checking Resource Status

You can either display all resources used by the system equipment or resources used by extended boards installed in the system equipment.

Checking Resources Used by the System

1.In the [ISA Configuration Utility] window, open the [View] menu, and select [System Resources...].

NOTE: On the screen shown below, “Card” is displayed for extended boards.

ISA Configuration Utility

File Configure View Advanced Help

Add	Remove	Modify	View
		System Resources...
Card Configured In System:
		Card Resources...
Motherboard System Devices
PCI Card: VGA Controller
PCI Card: SCSI Controller
PCI Card: Unknown Card
PCI Card: IDE Controller

Resources currently in use by the system equipment are displayed in the [System Resource Usage] dialog box.

[		]	System Resource Usage

Resources utilized by current system configurarion:

IRQ:

0

1

2(9)

Used By Card...

DMA:

2

4

Close

Memory [hex]:

0 - 9ffff

e0000 - fffff

100000 - 1ffffff

Print To File...

I/O Port [hex]:

0 - f

20 - 21

2e - 2f

Help

2.After checking, choose [Close].

Hitachi VisionBase 8880R Server

41

Image 45

Contents Product Guide Hitachi VisionBase 8880R ServerTrademarks CopyrightDisclaimer Issue Date November Part Number 202-85031-01-Rev AContents 3 Error Information POST Error System Beeps System Specifications 1 HardwareSystem Overview 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSI Hitachi VisionBase 8880R Server Powering-On the System Figure 1 Accessing the Power SuppliesFigure 2 Accessing the Power Supplies Front Panel Figure 3 P/S Receptacle and On/Off SwitchFigure 4 Front Panel Detail Back Panel Figure 6 Direct Boot Switch DetailFigure 5 Back Panel Detail Detail ASafety Guidelines Removing the Server Panels and Accessing Its ComponentsWarnings and Cautions Tools and Supplies You NeedFigure 7 Accessing the Option Slots Accessing the PCI SlotsFigure 8 Option Slots PCI/ISA Option BoardsHard Disk Drives Figure 9 Accessing the Hard Disk DrivesSCSI SCA Hard Disk Drives Figure 10 Hard Disk Drive BaysFigure 11 Removing/Installing a HDD Installing/Swapping a HDDOptional Devices Figure 12 Mounting the HDD CarrierHDD HDD Position Pins HDD Carrier 4 Mounting Screws Figure 13 Memory and CPU Slots Figure 14 CPU/VRM Installation DetailMemory The system supports the following specifications for memory DIMMs Figure 15 Memory Board Slot LocationFigure 16 System Board Default Jumper Settings Jumper SettingsVRM #3 VRM #4Figure 17 I/O Board Switch Settings 2 System Environment Setting Flow of System Environment SettingBefore Operations Outline of the Setup Menu What You Can Do with the System Environment SettingSetting for Each Board Outline of ISA Configuration Utility ICUNotes on Use PCI BoardFlow of the Setup Menu Operation Setup MenuFigure 18 Entering Setup Menu Starting the Setup MenuSetup Menu Screen Configuration of the Setup Menu ScreenFigure 19 Setup Menu Screen Configuration In the Setup Menu, the following key operations are allowed Operating the Keys on the Setup MenuSteps for Setting the Setup Menu What You Can Do on the Main MenuFigure 20 Main Menu Screen System Time and System Date Legacy Diskette A,BPrimary Master Slave Execute ROM Diagnostic Unsupported Reset Configuration DataWhat You Can Do on the Advanced Menu Network serverI/O Device Configuration PCI ConfigurationSelect Resources Current ResourcesFloppy disk controller Parallel portLocal Bus IDE adapter PS/2 MouseEnable memory gap Ext MP Configuration TableConsole Redirection Unsupported I/O APIC ModeLarge Disk Access Mode Unsupported WinNT 4.0 Install ModeSpeaker Volume Caching Above 4GBUser Password is Supervisor Password isSet Supervisor Password Set User PasswordWhat You Can Do on the Boot menu Figure 23 Boot Menu ScreenHard Drive IDE Hard Disk Drive Exit Saving Changes What You Can Do on the Exit MenuExit Discarding Changes Figure 24 Exit Menu ScreenNotes on the Setup Menu ISA Configuration Utility ICULoad Setup Defaults Discard ChangesFlow of Operation with the ICU Backup for ICU DiskStarting the ICU System ResourcesSpace Do not remove ICU DISK2 before the ICU terminatesICU Screen How to Use HelpOperating the ICU Figure 25 ICU ScreenExiting the ICU Checking Resources Used by the System Checking Resource StatusChecking Resources for Extended Boards Adding an Extended Board6. A dialog box for confirmation is displayed. Choose OK Changing the Settings in Extended Boards Settings for Each ResourceReserving I/O Port Addresses Removing an Extended Board When ICU Program Disk Has Been Destroyed Reserving Resources In Use from an ISA BoardNOTE Unknown Card is displayed for RAID controller PC-CA7112 Lock/Unlock Card Restoring Configuration InformationErrors and Countermeasures Restrictions on the ICU Returning the Settings of the Setup Information to Defaults Returning the Settings to DefaultsReturning the ICU Settings to Defaults List of Utility SettingsCh 2 System Environment Setting Fixed ConfigurationThis table defines the SCSI Select factory default settings Symbios Logic SCSI Configuration UtilitiesPOST Error 3 Error InformationCh 3 Error Information Hitachi VisionBase 8880RSystem Beeps 2. Select Advanced Menu-Windows NT 4.0 Install Mode Installing Windows NT4 NT Drivers and Limitations Windows NT Driver RecommendationsHitachi VisionBase 8880R 5 Related Document and Specification Environment SpecificationRelated Document Hitachi VisionBase 8880R Ch 5 Related Document and Specification