Hitachi 8880R manual ISA Configuration Utility ICU, Notes on the Setup Menu, Load Setup Defaults

Page 40

Load Setup Defaults

Ch 2: System Environment Setting

Load Setup Defaults

Returns the setup data to the defaults. The settings in the following items are not to be changed. This function is equivalent to F9 key.

•

•

•

•

System Time

System Date

User Password

Administrative Password

Discard Changes

Returns the settings other than those below to the last recorded setup data. This function is equivalent to

•System Time

•System Date

•User Password

•Administrative Password

F6

key.

Save Changes

Records setup data without exiting the Setup menu.

Notes on the Setup Menu

•

•

•

Only 3.5-inch, 720 KB or 1.44MB floppy disks must be used. Functions related to the IDE hard disk are unsupported. “Console Redirection” in the Advanced menu are unsupported.

If you use values other than those recommended, evaluate such values sufficiently before use. Hitachi PC assumes no responsibility for any trouble caused by the use of unrecommended values.

ISA Configuration Utility (ICU)

The ISA Configuration Utility (ICU) is a software product that enables ISA-specification extended boards not conforming to Plug and Play to be used correctly in the system equipment. When you expand your system, make appropriate settings in the Setup Menu and use the ICU to perform configuration. The settings are stored in nonvolatile memory of the system equipment.

It is recommended that the user configure the ISA card first, using the ICU, before installing it in the system.

In one of the following cases, start the ICU and make settings.

•

•

•

When the configuration of the system equipment is changed

When checking or setting resources for various types of board controllers

If a configuration error message is displayed at power-on

NOTE: The ISA boards supported by the Hitachi VisionBase 8880R Server system equipment (PC-CH2100 and PC-SHT4840-IS) are incompatible to Plug and Play.

The Hitachi VisionBase 8880R Server system equipment does not support Plug and Play compatible operating systems.

36	Hitachi VisionBase 8880R Server

Image 40

Contents Hitachi VisionBase 8880R Server Product GuideCopyright TrademarksDisclaimer Issue Date November Part Number 202-85031-01-Rev AContents 3 Error Information POST Error System Beeps 1 Hardware System SpecificationsSystem Overview 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSI Ch 1 Hardware Figure 1 Accessing the Power Supplies Powering-On the SystemFigure 2 Accessing the Power Supplies Figure 3 P/S Receptacle and On/Off Switch Front PanelFigure 4 Front Panel Detail Figure 6 Direct Boot Switch Detail Back PanelFigure 5 Back Panel Detail Detail ARemoving the Server Panels and Accessing Its Components Safety GuidelinesWarnings and Cautions Tools and Supplies You NeedAccessing the PCI Slots Figure 7 Accessing the Option SlotsPCI/ISA Option Boards Figure 8 Option SlotsFigure 9 Accessing the Hard Disk Drives Hard Disk DrivesSCSI SCA Hard Disk Drives Figure 10 Hard Disk Drive BaysInstalling/Swapping a HDD Figure 11 Removing/Installing a HDDFigure 12 Mounting the HDD Carrier Optional DevicesHDD HDD Position Pins HDD Carrier 4 Mounting Screws Figure 14 CPU/VRM Installation Detail Figure 13 Memory and CPU SlotsMemory Figure 15 Memory Board Slot Location The system supports the following specifications for memory DIMMsJumper Settings Figure 16 System Board Default Jumper SettingsVRM #3 VRM #4Figure 17 I/O Board Switch Settings Flow of System Environment Setting 2 System Environment SettingBefore Operations What You Can Do with the System Environment Setting Outline of the Setup MenuOutline of ISA Configuration Utility ICU Setting for Each BoardNotes on Use PCI BoardSetup Menu Flow of the Setup Menu OperationStarting the Setup Menu Figure 18 Entering Setup MenuConfiguration of the Setup Menu Screen Setup Menu ScreenFigure 19 Setup Menu Screen Configuration Operating the Keys on the Setup Menu In the Setup Menu, the following key operations are allowedWhat You Can Do on the Main Menu Steps for Setting the Setup MenuFigure 20 Main Menu Screen Legacy Diskette A,B System Time and System DatePrimary Master Slave Reset Configuration Data Execute ROM Diagnostic UnsupportedWhat You Can Do on the Advanced Menu Network serverPCI Configuration I/O Device ConfigurationSelect Resources Current ResourcesParallel port Floppy disk controllerLocal Bus IDE adapter PS/2 MouseExt MP Configuration Table Enable memory gapConsole Redirection Unsupported I/O APIC ModeWinNT 4.0 Install Mode Large Disk Access Mode UnsupportedSpeaker Volume Caching Above 4GBSupervisor Password is User Password isSet Supervisor Password Set User PasswordFigure 23 Boot Menu Screen What You Can Do on the Boot menuHard Drive IDE Hard Disk Drive What You Can Do on the Exit Menu Exit Saving ChangesExit Discarding Changes Figure 24 Exit Menu ScreenISA Configuration Utility ICU Notes on the Setup MenuLoad Setup Defaults Discard ChangesBackup for ICU Disk Flow of Operation with the ICUSystem Resources Starting the ICUSpace Do not remove ICU DISK2 before the ICU terminatesHow to Use Help ICU ScreenOperating the ICU Figure 25 ICU ScreenExiting the ICU Checking Resource Status Checking Resources Used by the SystemAdding an Extended Board Checking Resources for Extended Boards6. A dialog box for confirmation is displayed. Choose OK Settings for Each Resource Changing the Settings in Extended BoardsReserving I/O Port Addresses Removing an Extended Board Reserving Resources In Use from an ISA Board When ICU Program Disk Has Been DestroyedNOTE Unknown Card is displayed for RAID controller PC-CA7112 Restoring Configuration Information Lock/Unlock CardErrors and Countermeasures Restrictions on the ICU Returning the Settings to Defaults Returning the Settings of the Setup Information to DefaultsReturning the ICU Settings to Defaults List of Utility SettingsFixed Configuration Ch 2 System Environment SettingSymbios Logic SCSI Configuration Utilities This table defines the SCSI Select factory default settings3 Error Information POST ErrorCh 3 Error Information Hitachi VisionBase 8880RSystem Beeps Installing Windows NT 2. Select Advanced Menu-Windows NT 4.0 Install Mode4 NT Drivers and Limitations Windows NT Driver RecommendationsCh 4 NT Drivers and Limitations Environment Specification 5 Related Document and SpecificationRelated Document Ch 5 Related Document and Specification Hitachi VisionBase 8880R