Hitachi Fixed Configuration, Hitachi VisionBase 8880R Server, Ch 2 System Environment Setting

Page 55

		Ch 2: System Environment Setting


	Item	Default Setting Value

	Mouse Controller	Choice 1
	IRQ	12
	DMA	None
	Memory [Hex]	None
	I/O port [Hex]	None

	Parallel port	Choice 2
	IRQ	7
	DMA	3
	Memory [Hex]	None
	I/O port [Hex]	378–37f

	PCI Card: IDE Controller

	IDE Controller	Fixed Configuration

	Unknown Controller	Enabled
	IRQ	None
	DMA	None
	Memory [Hex]	None
	I/O port [Hex]	None

	Bridge Controller	Disabled
	IRQ	None
	DMA	None
	Memory [Hex]	None
	I/O port [Hex]	None

	PCI Card: VGA Controller

	VGA Controller	Fixed Configuration
	IRQ	None
	DMA	None
	Memory [Hex]	A000–bffff
		C000–c7fff
		Fd000000
		Fdffffff
	I/O port [Hex]	3b0–3bb
		3c0–3df

Hitachi VisionBase 8880R Server

Image 55

Contents Product Guide Hitachi VisionBase 8880R ServerIssue Date November Part Number 202-85031-01-Rev A CopyrightTrademarks DisclaimerContents 3 Error Information POST Error System Beeps 1 Hardware System SpecificationsSystem Overview 6 SCA2 Disk Bay SAF-TE Hot-swappable disk bay compliant SCSI Hitachi VisionBase 8880R Server Figure 1 Accessing the Power Supplies Powering-On the SystemFigure 2 Accessing the Power Supplies Front Panel Figure 3 P/S Receptacle and On/Off SwitchFigure 4 Front Panel Detail Detail A Figure 6 Direct Boot Switch DetailBack Panel Figure 5 Back Panel DetailTools and Supplies You Need Removing the Server Panels and Accessing Its ComponentsSafety Guidelines Warnings and CautionsFigure 7 Accessing the Option Slots Accessing the PCI SlotsFigure 8 Option Slots PCI/ISA Option BoardsFigure 10 Hard Disk Drive Bays Figure 9 Accessing the Hard Disk DrivesHard Disk Drives SCSI SCA Hard Disk DrivesFigure 11 Removing/Installing a HDD Installing/Swapping a HDDFigure 12 Mounting the HDD Carrier Optional DevicesHDD HDD Position Pins HDD Carrier 4 Mounting Screws Figure 13 Memory and CPU Slots Figure 14 CPU/VRM Installation DetailMemory The system supports the following specifications for memory DIMMs Figure 15 Memory Board Slot LocationVRM #4 Jumper SettingsFigure 16 System Board Default Jumper Settings VRM #3Figure 17 I/O Board Switch Settings Flow of System Environment Setting 2 System Environment SettingBefore Operations Outline of the Setup Menu What You Can Do with the System Environment SettingPCI Board Outline of ISA Configuration Utility ICUSetting for Each Board Notes on UseFlow of the Setup Menu Operation Setup MenuFigure 18 Entering Setup Menu Starting the Setup MenuConfiguration of the Setup Menu Screen Setup Menu ScreenFigure 19 Setup Menu Screen Configuration In the Setup Menu, the following key operations are allowed Operating the Keys on the Setup MenuWhat You Can Do on the Main Menu Steps for Setting the Setup MenuFigure 20 Main Menu Screen Legacy Diskette A,B System Time and System DatePrimary Master Slave Network server Reset Configuration DataExecute ROM Diagnostic Unsupported What You Can Do on the Advanced MenuCurrent Resources PCI ConfigurationI/O Device Configuration Select ResourcesPS/2 Mouse Parallel portFloppy disk controller Local Bus IDE adapterI/O APIC Mode Ext MP Configuration TableEnable memory gap Console Redirection UnsupportedCaching Above 4GB WinNT 4.0 Install ModeLarge Disk Access Mode Unsupported Speaker VolumeSet User Password Supervisor Password isUser Password is Set Supervisor PasswordFigure 23 Boot Menu Screen What You Can Do on the Boot menuHard Drive IDE Hard Disk Drive Figure 24 Exit Menu Screen What You Can Do on the Exit MenuExit Saving Changes Exit Discarding ChangesDiscard Changes ISA Configuration Utility ICUNotes on the Setup Menu Load Setup DefaultsFlow of Operation with the ICU Backup for ICU DiskDo not remove ICU DISK2 before the ICU terminates System ResourcesStarting the ICU SpaceFigure 25 ICU Screen How to Use HelpICU Screen Operating the ICUExiting the ICU Checking Resources Used by the System Checking Resource StatusChecking Resources for Extended Boards Adding an Extended Board6. A dialog box for confirmation is displayed. Choose OK Settings for Each Resource Changing the Settings in Extended BoardsReserving I/O Port Addresses Removing an Extended Board Reserving Resources In Use from an ISA Board When ICU Program Disk Has Been DestroyedNOTE Unknown Card is displayed for RAID controller PC-CA7112 Lock/Unlock Card Restoring Configuration InformationErrors and Countermeasures Restrictions on the ICU List of Utility Settings Returning the Settings to DefaultsReturning the Settings of the Setup Information to Defaults Returning the ICU Settings to DefaultsCh 2 System Environment Setting Fixed ConfigurationThis table defines the SCSI Select factory default settings Symbios Logic SCSI Configuration UtilitiesHitachi VisionBase 8880R 3 Error InformationPOST Error Ch 3 Error InformationSystem Beeps Windows NT Driver Recommendations Installing Windows NT2. Select Advanced Menu-Windows NT 4.0 Install Mode 4 NT Drivers and LimitationsHitachi VisionBase 8880R Environment Specification 5 Related Document and SpecificationRelated Document Hitachi VisionBase 8880R Ch 5 Related Document and Specification

Ch 2: System Environment Setting

Fixed Configuration