Hitachi HOME-1 Power ON/OFF, Turning On The Power, When the lens cap is attached, remove

Page 14

Power ON/OFF

Turning On The Power

WARNING • When the power is ON, a strong light is emitted. Do not look into the lens or vents of the projector.

NOTE • Turn the power on/off in right order. Please power on the projector before the connected devices. Power off the projector after the connected devices.

1 Make sure that the power cord is firmly and correctly connected to the projector and outlet.

POWER indicator

TEMP

POWERLAMP

STANDBY/ON INPUT

MENU

2	When the lens cap is attached, remove
	the lens cap.

STANDBY/ON button

3 Set the power switch to [ ] (ON).

Power switch (ON position)

The POWER indicator will light orange.

4 Press the STANDBY/ON button of the projector or the ON button of the remote control.

The projector lamp will light up and the POWER indicator will begin blinking green.

According to a setup, the projector lamp may light up and the POWER indicator may begin blinking green, without pressing this button.

When the power is completely on, the indicator will stop blinking and light green.

Power switch

ON button

ON

SEARCHOFF

SRC

VIDEO S-VIDEO COMPONENT

V SV C

COMPUTERVOLUME

PC

14

Image 14

Contents HOME-1 ProjectorProjector Features PreparationContents Fastening The Lens Cap Part NamesProjector Projector ON/OFFTo adjust the volume Remote ControlTo adjust the keystone Component VideoSetting Up ArrangementAdjust the height of the projector by Adjusting The Projectors ElevatorUsing The Picture Shift Dials As necessary, you can also finelyConnecting Your Devices Connecting to a computer AUDIO-L AUDIO-R G B RConnecting Power Supply Close Battery cover Remote ControlRemove Battery cover Putting BatteriesOperating The Remote Control When the lens cap is attached, remove Power ON/OFFTurning On The Power Set the power switch to onUsing the remote control Press the COMPUTER, VIDEO, S-VIDEO Selecting An Input SignalUsing the projector’s control button Press the Input buttonPower switch OFF position Turning Off The PowerSwitch the power switch to O OFF Attached the lens capTemporarily Muting The Sound Adjusting The VolumeOperating Using The Automatic Adjustment Feature Correcting Keystone DistortionsTemporarily Blanking The Screen Signal SearchingSelecting The Aspect Ratio Selecting The Gamma Mode Recalling Your AdjustmentsMultifunctional Settings Using The Menu FunctionsMain Menu Picture 1 Menu Picture 1 Menu Load/Save a SettingReset the PICTURE-1 Menu Items MY MemoryPosition PhasePicture 2 Menu SizeFrame Lock Input MenuVideo 3D-YCSInformation Input MenuVideo NR S2-ASPECTSearch AdjustAuto Menu Message Screen MenuStart UP Lamp Time VolumeOption Menu Lamp Replacing The Lamp Air Filter Caring For The Air FilterHold the release buttons of the air Replacing The Air FilterNew air filter. Tell the dealer your air Filter, while pulling down itCaring For The Inside Of The Projector Caring For The Cabinet And Remote ControlOther Care Caring For The LensTroubleshooting Related MessagesRelated Messages Regarding The Indicator Lamps Power Lamp TempRegarding The Indicator Lamps IndicatorPhenomena That May Easily Be Mistaken For Machine Defects Warranty And After-Service Phenomena That May Easily Be Mistaken For Machine DefectsRGB Input Ports Audio Ports SpecificationsSpecification Video Input PortsSignal Connectors TechnicalText Example Of Computer SignalResolution FH kHz FV Hz Rating Signal mode Initial Set Signals RS-232C Communication Connecting The CableCommunications Setting Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCommand Data Chart 4A D2日本語 Be EF EF F6 Be EF EC D9 Auto RGB Be EF CB D3 Turn on Be EF