Hitachi HDPJ52 user manual Connecting the power supply, Using the cable cover

Page 17

17

Cable cover

Connecting the power supply

Preparations

Before connecting the power, make sure that the power switch is in the OFF position (the side marked “O”).

1. Connect the power cord connector to the projector’s AC inlet.

2. Plug the power cord's plug ﬁrmly into a power outlet.

Power switch

Power cord connector

ENGLISH

AC inlet

WARNING ► Use extra caution when connecting the power cord as incorrect or faulty connections may result in ﬁre and/or electrical shock.

•Use only the power cord that came with the projector. If it becomes damaged, contact your dealer for a new one.

•Only plug the power cord into an outlet rated for use with the power cord's speciﬁed voltage range.

•Never modify the power cord. Never attempt to defeat the ground connection of the three-pronged plug.

•The power outlet should be close to the projector and easily accessible.

•Do not touch the power cord with wet hands.

•Check that the power cord connector is clean (no dust) before using. Use a soft, dry cloth to clean the power cord.

•Insert the power plug into the power outlet ﬁrmly. Avoid using loose, unsound outlets and contact failures.

Using the cable cover

Use of the accessory cable cover is recommended when the projector is suspended from the ceiling. The cable cover collects the cables together and

prevents slack cables from hanging down	Bottom of the	Screws for cable
from the ceiling.	projector	cover
To attach the cable cover to the projector,
please use the following procedure.

1. Loosen the 2 screws on the cable cover and also the screw for the cable cover on the rear of the projector.

2. Attach the cable cover to the projector, bundling the connected cables and running them through the window of the cable cover.

3. Retighten the screws that were loosened in the previous step to lock the cover in place.

Image 17

Contents Trademark acknowledgment Thank you for purchasing this projectorPreparations Before useProjection Basic operationTroubleshooting MaintenanceWarranty and after-service Speciﬁcations Advanced MenuAbout this manual Projector featuresAbout contents of package Projector Part namesComponent Video Control buttonsPorts PC, HDMI, Compo Remote controlCONTRAST, Bright Strap hole Rivet Fastening the lens coverStrap On a horizontal surface Suspended from the ceiling ArrangementFor 43 screens For 169 screensAdjusting the projector’s elevation With a VCR/DVD player Connecting your devicesFor an Scart RGB input For an Hdmi signal sourceFor a DVI signal source Optional Use With a computerAbout Plug-and-Play capability Computer signal examplesVesa Text VesaUsing the cable cover Connecting the power supplyLoading batteries into the remote control Using the remote control button lights Using the remote controlRemote control Sensor Approximately Light buttonPower button Turning the power onPower indicator STANDBY/ON buttonAutomatically adjusting the picture Selecting an input signalAdjusting the zoom Adjusting the display positionAdjusting the focus Zoom ringTurning the power off 169  For no signal or an unrecognized signal 169 ﬁxedWide MOVIE1 MOVIE2Dark BrightTemp Mode Gamma Color IrisNormal Standard Cinema LOWTurn OFF Bright DarkAUTO1 AUTO2MY Memory To load saved adjustment settings MY MEMORY To save adjustment settingsTo switch from the Advanced Menu to the Easy Menu To display a menu when no menu is currently displayedEasy Menu operation To change the display languageEasy Menu functions To reset the operationTo operate the selected item To close the menu Cinema LOW  Normal Cinema High  MusicWeaker  Stronger Darker  BrighterReddish  Greenish MirrorEnglish  Français  Deutsch  Español ResetItaliano  Norsk  Nederlands  Português Language Svenska  Русский  Suomi  Polski  TürkçeAdvanced Menu operation To switch from the Easy Menu to the Advanced MenuTo select a menu To reset the menu settings Standard Picture menu High  CUSTOM-1, CUSTOM-2, CUSTOM-3, CUSTOM-4Step Ramp Gray scale Description To adjust a Custom mode6500K  7500K  9300K  Hi-BRIGHT These modes set the same color temperature as the mode nameCUSTOM-1  CUSTOM-2  CUSTOM-3  CUSTOM-4  6500K, 7500K, 9300KGreenish  Reddish Step  Ramp Gray scaleIris Memory Description To save adjustment settingsOver Scan Using the / cursors buttons changes the aspect ratioImage menu  For a signal from the Hdmi port  For a signal from the Computer port For a signal from the Component Video ports  For a signal from the S-VIDEO or Video portTV  Film  Turn OFF Input menu Film  Auto Component Component  Scart RGB Scart RGB  NTSC, PAL, SECAM, NTSC4.43, M-PAL, N-PALExample for an Hdmi signal Example for computer RGB signalsExample for a video, s-video and component video signal Example for a Scart RGB signalReduce top of the image  Reduce bottom of the image Setup menuKeystone Normal  WhisperMenu Position Screen menuLanguage  MyScreen MyScreen  Original  Turn OFFStart UP  OriginalMessage To move the black bars up and down Using the / cursor buttons switches between the dialogsLong max min.  Short min min Reset  CancelOption menu Using the / cursor buttons changes the rotation FAN Speed  Ghost  Stripe Factory Reset  Filter MessageHigh  Normal Ghost50h  100h  200h  300h  Turn OFF Factory ResetFilter Message Lamp Bottom Projector Lamp cover Screw Replacing the lamp by yourselfAir ﬁlter Knobs Air ﬁlterFilter Maintenance Lens Cabinet and Remote controlInside of the projector Horizontal or vertical wavelength of the input signal There is no input signalInternal temperature is high Related messagesPower Lamp Temp Regarding the indicator lampsIt is time to clean the air ﬁlter Indicator Cooling fan is not operatingThere is a possibility that the interior of the projector Has overheatedBy a power outage blackout, etc Main power source has been interrupted during operationSignal cables are not correctly connected Lens cover is closedMenu function or the remote control Brightness is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableWhisper function is working Set the Whisper item 48 in the Setup menu to NormalWhisper function may cause screen ﬂicker Fan speed has been automatically changedRGB input port SpeciﬁcationDigital input port Communication portUnit mm Dimension diagramInterface which is an interface standard for Entry Explanation40, 43, 44 NtscSecam PALScart